background image

© UPLIFT Desk

 • 1-800-349-3839 • [email protected] • www.upliftdesk.com

Step 3 

(Optional - if your desk is NOT 30 inches deep)

Determine whether or not the placement of the angled brace is right 
for your desktop. If your desktop is 30’’ deep, the brace is shipped in 

the correct position (see fig. 1), Proceed to step 4. 

 

 
For desktops that are 24’’ deep, the brace should be moved  

to the last row of holes, as seen in fig. 2. 

To adjust the position of the angled brace, remove the bolts with  
the small Allen wrench, move the angled brace to the desired  
placement and reattach the bolts with the small Allen wrench.

Follow this step carefully to avoid injury

Do not squeeze the paddle at this time

fig. 2. placement for 
desktops 24’’ deep

fig. 1. placement for 
desktops 30’’ deep

Step 6

Place your hand firmly flat on top of the square end of the lifting 

 

mechanism prior to squeezing the paddle. See diagram for hand 
placement. Your hand will prevent the mechanism from rising 

 

too quickly.

 

With your hand firmly on the square end of the lifting mechanism,  
squeeze the paddle with the other hand and 

slowly

 guide the  

lifting mechanism up to its highest point. 

Upon squeezing the paddle, the 

l

ifting mechanism will rise with 

force, so it is important to hold the mechanism 

firmly

Release the paddle to lock in place.

Step 4 

(Optional)

We’ve mounted the keyboard tray so it’s lower than the desk surface. 
We recommend you leave it by skipping this step. This will allow you 
to have your keyboard platform at the best ergonomic height while 
you are seated. 

If you want your keyboard tray to be higher up, remove the bolts  
that connect the front panel to the current vertical connector using 
the small Allen wrench (Part H). Attach the short vertical connector 
(Part D) to the front panel using the bolts you just removed.

Step 5

Before you screw the front panel onto the Adapt Clamp main assem-

bly, make sure that the cable attached to the paddle is configured as 

shown in the diagram to the right. 

Unpack the Adapt Clamp™ main assembly (Part A) and orient it with 
the upper work surface face down. 

Attach the front panel assembly (Part C) onto the Adapt Clamp™ 
main assembly (Part A) using the M6x12 bolts (Part J) and the smaller 
Allen wrench (Part H).

CAUTION

!

CAUTION

!

!

Summary of Contents for UDA100-clamp

Page 1: ... than 1 5 Step 2 Loosen the long bolts under the clamp assembly enough to allow you to slide the entire assembly onto the back edge of your desktop Hold the clamping plate between the desk and the long bolts aligning the holes in the plate with the ends of the bolts Tighten the long bolts with the larger Allen wrench Part G to secure the clamp onto the desk Part C front panel assembly Parts D shor...

Page 2: ... lifting mechanism squeeze the paddle with the other hand and slowly guide the lifting mechanism up to its highest point Upon squeezing the paddle the lifting mechanism will rise with force so it is important to hold the mechanism firmly Release the paddle to lock in place Step 4 Optional We ve mounted the keyboard tray so it s lower than the desk surface We recommend you leave it by skipping this...

Page 3: ... the vertical connector under the main assembly s work surface Attach keyboard tray to the main assembly using two M6 8 bolts Part I and tighten using the small Allen wrench Part H Optional Cover the bolts with the adhesive bolt covers Part F by centering the sticky side on the heads of the exposed bolts Adhere the pad around the bolt by pressing all around the bolt This will prevent scratches to ...

Page 4: ...FT Adapt Clamp is 28 6 lbs Do not overload Failing to follow these assembly instructions and safety precautions may result in personal injury Failing to follow these assembly instructions and safety precautions voids your warranty and may result in property damage CAUTION Copyright Notice This guide is a component of the UPLIFT Adapt Clamp This guide is a part of the scope of delivery even if the ...

Reviews: