manualshive.com logo in svg

Universal HP-100NI, Owner'S Manual

Share
Download
Universal HP-100NI Owner'S Manual Download Page 18

Page 18 of 26

ASSEMBLY OF THE INK ROLLER ECCENTRIC

Proper installation of the Ink Roller Eccentric Assembly is critical to the perfor-
mance of the coder and uniform inking of the printing dies.  It is easiest to as-
semble these parts properly with the Side Frame removed from the coder.

1 -Loosen the nylon tipped Tension Adjusting

Set Screw.

2 -Install one of the Delrin Washers on  the

Eccentric Adjusting Knob.

3 -Insert the Eccentric Adjusting  Knob through

the large hole in the Side Frame.

4 -Install the remaining Delrin Washer on the

Eccentric Adjusting Knob.

This set screw is used to keep tension on the Ec-
centric Knob and prevent the Ink Roller from mov-
ing out of position after it is properly adjusted.

Figure 49

Figure 50

Figure 51

Figure 52

Apply a thin film of grease on the shoulder of the
Eccentric Adjusting Knob after the Delrin Washer is
installed.

Note:  The knurled head of the Eccentric must  be
on the opposite side from the milled flat  on the Side
Frame.

MAINTENANCE

Summary of Contents for HP-100NI



























Reviews:

No comments

Brands by name

Popular brands

Load more brands