background image

 

can set the heater to power on after 1 to 15 hours by press 

“+” and “

-

”. 

 

2.3.

 

Power  on:  In  standby  mode,  press 

“ON/OFF”

  to  start  up,  the  heater  will  start  working  with 

2200W, all heating indicator 

 light up. 

2.4.

 

Power off: In power on mode, press 

“ON/OFF” again to shut down, the heater will enter

 standby 

mode. (except when the heater enters to 

“open window”

 mode) 

2.5.

 

Mode switch

: press “

M

ode”,

 you can freely switch between any of the below 4 modes. 

Mode 

Adjust power 

  Adjust set temperature 

    Timing 

Weekly 

timing 

Normal mode 

All power output (4 tubes light up) to 

half power output (2 tubes light up) 

Cannot set temperature 

(Fixed at 38

Set from 1 hour 

to 15 hours 

Not 

Applicable 

Automatic mode 

Automatically by thermostat   

Half / full power (2/4 tubes) 

15

-32

 

Cannot set 

Not 

Applicable 

Sleep mode 

All power output (4 tubes light up) 

Cannot set temperature 

(Fixed at 28

Set from 1 hour 

to 15 hours 

Not 

Applicable 

Power saving 

mode 

Automatically by thermostat or timer   

Half / full power (2/4 tubes) 

15

-32

 

Cannot set 

YES 

 

3. Mode operation 

3.1. Normal mode: 

In  normal  mode,  the  heater  will  start 

“temperature  sensing”

  status  and 

“o

pen  window  temperature 

sensing”

 status, their description as below: 

T

emperature sensing”

 description

: When the heater is working with full power (four tubes all light up), if 

the sensor detects the ambient temperature is higher than 38

, two tubes on the heater will go out and 

the other two tubes will keep lighting up. When the sensor detects the ambient temperature is below 38

the heater will resume working with full power (four tubes will all light up). 

O

pen window temperature sensing”

 description: 

When the heater is working with full power (four tubes 

all light up), if the sensor detects a sudden ambient temperature decline of 5

 within 300 seconds, two 

tubes  on  the  heater  will  go  out  and  the  other  two  tubes  will  keep  lighting  up.    The  open  window 

indication 

 lights up, you can close the open window indication by any button, then the heater will 

resume heating with full power (four tubes all light up).

 

Summary of Contents for UHQ-887












Reviews: