background image

10 

40% in the dehumidifying mode. The default dehumidifier setting for the dehumidifier 
mode is 40% 

5. Press

to set the timer function: 

Press 

 

to set the auto turn-on time when the unit is in stand-by mode and 

switched on, the LED will display the time set from 1-24 hours, so the unit will auto 
turn on after the setting time.   

Press 

  to set the auto turn-off time when the unit is in operating function, the 

LED will display the time set from 1-24 hours, so the unit will auto turn off after the 
setting time.   

If the unit is turned on or off by operation or water-full mode, then the auto turn on/off 

function will be canceled.     

6. Press the

key to adjust the working mode, there exist two working models, 

dehumidifying mode and continuous mode. 

DRAINING THE COLLECTED WATER 

When the drainage tank is full, the tank full indicator light will turn on, the operation 
will stop automatically and the buzzer will beep 15 times to alert the user that the 
water needs to be emptied from the drainage tank . 

Emptying the Drainage Tank 

1.

Lightly press on the sides of the tank with both hands and pull the tank out gently.

2.

Discard the collected water

Summary of Contents for DUE-1239























Reviews: