background image

-2-

• 

IMPORTANT: Read this entire manual before installing 

and  operating  this  product.  Failure  to  do  so  may 

result  in  property  damage,  bodily  injury,  or  even 

death. Proper installation of this stove is crucial for 

safe and efficient operation.

• 

Install  vent  at  clearances  specified  by  the  vent 

manufacturer. 

• 

Do not connect the pellet vent to a vent serving any 

other appliance or stove.

• 

Do not install a flue damper in the exhaust venting 

system of this unit.

• 

Use of outside air is not required for this unit. 

• 

Contact  your  local  building  officials  to  obtain  a 

permit and information on any additional installation 

restrictions or inspection requirements in your area.

• 

Do  not  throw  this  manual  away.  This  manual  has 

important operating and maintenance instructions 

that you will need at a later time. Always follow the 

instructions in this manual.

• 

This appliance is designed for the use of pelletized 

fuel  that  meet  or  exceed  the  standard  set  by  the 

Pellet Fuel Institute(PFI).

• 

Never  use  gasoline,  gasoline-type  lantern  fuel, 

kerosene, charcoal  lighter  fluid,  or similar  liquids  to 

start or ’freshen up’ a fire in this stove. Keep all such 

liquids well away from the stove while it is in use.

• 

A working smoke detector must be installed in the 

same room as this product.

• 

Install a smoke detector on each floor of your home; 

incase  of  accidental  fire  from  any  cause  it  can 

provide time for escape.

• 

The  smoke  detector  must  be  installed  at  least  15 

feet (4,57 M) from the appliance in order to prevent 

undue triggering of the detector when reloading.

• 

Do not unplug the stove if you suspect a malfunction. 

Turn the ON/OFF SWITCH to ”OFF’ and contact your 

dealer.

• 

Your  stove  requires  periodic  maintenance  and 

cleaning  (see  ”Maintenance”).  Failure  to  maintain 

your  stove  may  lead  to  improper  and/or  unsafe 

operation.

• 

Disconnect the power cord before performing any 

maintenance! NOTE: Turning the ON/OFF Switch to 

”OFF” does not disconnect all power to the electrical 

components of the stove.

• 

Never try to repair or replace any part of the stove 

unless  instructions  for  doing  so  are  given  in  this 

manual. All other work should be done by a trained 

technician.

• 

Do  not  operate  your  stove  with  the  viewing  door 

open.  The  auger  will  not  feed  pellets  under  these 

circumstances and a safety concern may arise from 

sparks or fumes entering the room.

• 

Allow  the  stove  to  cool  before  performing  any 

maintenance or cleaning. Ashes must be disposed 

in  a  metal  container  with  a  tight  fitting  lid.  The 

closed  container  of  ashes  should  be  placed  on  a 

non-combustible  surface  or  on  the  ground,  well 

away from all combustible materials, pending final 

disposal.

• 

The  exhaust  system  should  be  checked  monthly 

during the burning season for any build-up of soot 

or creosote. 

• 

Do not touch the hot surfaces of the stove. Educate 

all  children  on  the  dangers  of  a  high-temperature 

stove.  Young  children  should  be  supervised  when 

they are in the same room as the stove.

• 

The  hopper  and  stove  top  will  be  hot  during 

operation;  therefore,  you  should  always  use  some 

type of hand protection when refueling your stove. 

• 

A power surge protector is required. This unit must be 

plugged into a 110 - 120V, 60 Hz grounded electrical 

outlet.  Do  not  use  an  adapter  plug  or  sever  the 

grounding  plug.  Do  not  route  the  electrical  cord 

underneath, in front of, or over the heater. Do not 

route the cord in foot traffic areas or pinch the cord 

under furniture.

• 

The heater will not operate during a power outage. 

If a power outage does occur, check the heater for 

smoke  spillage  and  open  a  window  if  any  smoke 

spills into the room.

• 

The  feed  door  must  be  closed  and  sealed  during 

operation.

• 

Never block free airflow through the open vents of 

the unit.

• 

Keep foreign objects out of the hopper.

• 

The moving parts of this stove are propelled by high 

torque  electric  motors.  Keep  all  body  parts  away 

from  the  auger  while  the  stove  is  plugged  into  an 

electrical outlet. These moving parts may begin to 

move at any time while the stove is plugged in.

• 

Do not place clothing or other flammable items on 

or near this stove. 

• 

When installed in a mobile home, the stove must be 

grounded directly to the steel chassis and bolted to 

the floor. WARNING  - THIS UNIT MUST NOT BE INSTALLED 

IN THE BEDROOM. CAUTION - The structural integrity 

of the mobile home floor, wall, and ceiling/roof must 

be maintained. 

• 

This appliance is not intended for commercial use.

• 

CAUTION:  Burning  fuel  creates  carbon  monoxide 

and can be hazardous to your health if not properly 

vented.

• 

This  appliance  is  a  freestanding  heater.  It  is  not 

intended to be attached to any type of ducting. It 

is not a furnace.

Safety Precautions

Summary of Contents for VOGELZANG VG5501S





















































Reviews: