Olymberyl HF217-SE Baby Gabriel Instruction Manual Download

Page: 1 / 44

Olymberyl® HF217-SE Baby Gabriel

Defra Smoke Exempted Free-standing
Non-Boiler Wood Burner

Instruction Manual

Published November 2013

Please note This appliance has been

independently tested and approved

by Defra as an ‘exempted appliance’

to allow the burning of wood in

designated UK Smoke Control Areas

(see page 13). It must, at all times,

be operated in accordance with the

instructions to minimise the amount

of smoke produced.

You will need to refer to the serial

number of your stove shown above

should you ever need to make a claim

under the Hi-Flame Warranty. You will

also ﬁnd the serial number, beginning

with HF, on the CE plate at the rear of

the stove as well as on the lid of the

outer packaging.

This appliance has
been approved by Hetas

This appliance has been approved
by Hetas Limited speciﬁcally as an
intermittent operating appliance for
burning wood only. Please note that

Hetas Limited Appliance Approval

only

covers the use of wood fuels in this
appliance.

Hetas Limited Approval

does

not cover the use of other fuels, either
alone or mixed with wood, nor does
it cover instructions for the use of
other fuels.

��

Baby

�

��

��
��

��

Ref: HF217-SE / UK-NI-ROI / V7.05-01-16

Summary of Contents for HF217-SE Baby Gabriel













































Search results

Summary of Contents for HF217-SE Baby Gabriel

Reviews:

Related manuals for HF217-SE Baby Gabriel

Brands by name

Popular brands

Olymberyl HF217-SE Baby Gabriel, Instruction Manual

Search results

Summary of Contents for HF217-SE Baby Gabriel

Reviews:

Related manuals for HF217-SE Baby Gabriel

Brands by name

Popular brands