background image

Installation, Operation and Maintenance Manual

C13-Series

35

Subject to change without notice.

10.20-IM (0818)

Limited Warranty for Hermetic Compressors

United CoolAir warrants the hermetic compressor in this 

product to be free from defects in factory workmanship 

and material under normal use and service and will, at its 

option, repair or replace the hermetic compressor if it proves 

to have such defects within a period of one (1) year from 

the date of product installation, to begin no later than six 

(6) months after product shipment from the factory� This 

warranty extends only to the original consumer purchaser in 

accordance with the then current Terms and Conditions and 

is non-transferable�
For this warranty to apply, the product must be installed 

according to United CoolAir recommendations and 

specifications, and in accordance with all local, state, national 

and provincial codes� The product must not be moved from 

its original place of installation� A second compressor failure 

in the same refrigerant circuit is indicative of an application 

issue and will not be covered under the Limited Warranty�
This limited warranty applies only to products installed in the 

continental United States, Alaska, Hawaii, Puerto Rico and 

Canada�

EXCLUSIONS

This Limited Warranty does not cover:

1� 

Shipping, labor or material charges�

2� 

Damages resulting from transportation, installation or 

servicing�

3� 

Damages resulting from accident, abuse, fire, flood, 

alteration or acts of God�

4� 

Tampering with, altering, defacing or removing the 

product serial number will serve to void this warranty�

5� 

Damages resulting from use of the product in a 

corrosive atmosphere (such as concentrations of acids 

or halogenated hydrocarbons)�

6� 

Damages resulting from inadequacy or interruption of 

electrical service, improper voltage conditions, blown 

fuses, or other like circumstances�

7� 

Cleaning or replacement of filters or belts.

8� 

Damages resulting from failure to properly and 

regularly clean air and/or water side of condenser and 

evaporator�

9� 

Damages resulting from: (I) freezing of condenser 

water or condensate; (II) use of corrosive water; (III) 

fouling or restriction of the air/water circuit by foreign 

material or like causes�

10� 

Damages resulting from operation with inadequate or 

interrupted supply of air or water�

11� 

Damages resulting from use of components or 

accessories not approved by United CoolAir�

12� 

This warranty does not apply to the installation, 

plumbing and wiring not integral to the product�

13� 

Damages resulting from improper application or sizing�

14� 

Discharge air temperature control, if not provided by 

the factory, will void the compressor Limited Warranty�

15� 

In the event that the refrigerant type is changed, as 

a result of a compressor failure and the same type 

of compressor is not available, any subsequent 

compressor failures will not be covered under the 

Limited Warranty�

This warranty is in lieu of all other warranties, expressed or 

implied, including the implied warranties of merchantability 

and fitness for a particular purpose.
Some states (provinces) do not allow the disclaimer of 

implied warranty, so that the above disclaimer may not apply 

to you�
Some states (provinces) allow only a partial limitation on 

implied warranties to limit the duration of implied warranties 

to the duration of the express warranty� In such states 

(provinces), the duration of implied warranties is hereby 

expressly limited to the duration of the express warranty on 

the face hereof�
In no event, whether as a result of breach of warranty or 

contract, tort (including negligence) strict liability or otherwise, 

shall United CoolAir be liable for special, incidental, or 

consequential damages, including but not limited to loss 

of use of the equipment or associated equipment, lost 

revenues or profits, cost of substitute equipment or cost of 

fuel or electricity� The above limitations shall inure to the 

benefit  of  United  CoolAir’s  suppliers  and  subcontractors. 

The above limitation on consequential damages shall not 

apply to injuries to persons in the case of consumer goods�
Some states (provinces) do not allow the exclusion or 

limitation of liability for consequential damages, or for strict 

liability in tort, so that the above exclusions and limitations 

may not apply to you�
United CoolAir does not assume, or authorize any other 

person to assume for United CoolAir, any other liability for 

the sale of this product�
This warranty gives you specific legal rights. You may also 

have other rights which vary from state to state(province to 

province)�

To obtain warranty service

Contact the installing or servicing contractor with the details 

of the problem� Provide the model number, serial number 

and date of installation� Warranty requests directed to the 

factory will be referred back through the local distribution 

network�

Model:  ______________  

Serial Number:  _______________ 

Date of Installation:  ________

Summary of Contents for C13-Series














































Reviews: