United cool air C13-Series Installation, Operation And Maintenance Manual Download Page 3

Page: 3 / 45

Installation, Operation and Maintenance Manual

C13-Series

Subject to change without notice.

10.20-IM (0818)

Contents

Contents � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Wiring Diagram � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Important Notice� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5

Use of Symbols� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5

C13-Series Air-Cooled Package � � � � � � � � � � � � � � � � � � � 6

C13-Series Water-Cooled Package � � � � � � � � � � � � � � � � � 7

General Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

Inspection Of Equipment � � � � � � � � � � � � � � � � � � � � � � � � 8

Handling� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

Location � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

Mounting And Setting In Place� � � � � � � � � � � � � � � � � � � � 8

Installation� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9

Split Systems � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9

Separation Of Sections � � � � � � � � � � � � � � � � � � � � � � � � � � 9

Interconnecting Refrigerant Tubing � � � � � � � � � � � � � � � 10

Single Package Unit Wiring� � � � � � � � � � � � � � � � � � � � � � 13

Split System Wiring � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

Duct Connection� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

Pressure Switches � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

High Pressure � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

Low Pressure � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

Water-Cooled Condensing Units � � � � � � � � � � � � � � � � � 13

Water-Cooled Condenser� � � � � � � � � � � � � � � � � � � � � � � 13

Water Piping and Connections� � � � � � � � � � � � � � � � � � � 13

Hook Up � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14

Water Connection� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14

Condensate Drain Connection � � � � � � � � � � � � � � � � � � � 14

Maintenance Procedures� � � � � � � � � � � � � � � � � � � � � � � � 15

Filters� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15

Cleaning The Water-Cooled Condenser� � � � � � � � � � � � 15

Blowers � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 16

Blower Motors� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 17

Blower Speed Adjustment � � � � � � � � � � � � � � � � � � � � � � � 17

Blower Motor Lubrication � � � � � � � � � � � � � � � � � � � � � � � 17

Belts� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18

Refrigerant Systems� � � � � � � � � � � � � � � � � � � � � � � � � � � � 18

Evaporator And Air-Cooled Condenser Coils � � � � � � � 18

Minimum Service Access � � � � � � � � � � � � � � � � � � � � � � � 18

Application Data � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18

Hard Start Kit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18

Sequence Of Operation � � � � � � � � � � � � � � � � � � � � � � � � � 19

Cooling Sequence Of Operation � � � � � � � � � � � � � � � � � � 19

Heating Sequence Of Operation (Other Than Heat

Pump) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19

Heat Pump Heating Sequence Of Operation � � � � � � � � 20

Options � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20

Condensate Pump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20

Thermostat � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21

Checking Hot Gas Bypass Valve� � � � � � � � � � � � � � � � � � 21

Adjustment Of Hot Gas Bypass Valve � � � � � � � � � � � � � 22

Microprocessor Controller � � � � � � � � � � � � � � � � � � � � � � 22

Humidifier � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22

Electric Heat � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22

Electric Reheat � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22

Steam Coil� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22

Hot Water Coils� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23

Flooded Condenser � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23

Buck/Boost Transformer � � � � � � � � � � � � � � � � � � � � � � � � 23

Chilled Water Valves Or Hot Water Valves � � � � � � � � � � 24

Head Pressure Control Valves � � � � � � � � � � � � � � � � � � � 24

Economizer Operation (Airside) � � � � � � � � � � � � � � � � � � 24

Economizer Operation � � � � � � � � � � � � � � � � � � � � � � � � � 24

Economizer Operation – (Waterside) � � � � � � � � � � � � � � 24

Condensing Section Outdoor Modification Kit � � � � � � 24

Split Condenser / Condensing Sections � � � � � � � � � � � 24

C13-Series Air-Cooled Condenser/ Condensing Section

With Outdoor Modification Kit� � � � � � � � � � � � � � � � � � � � 25

Vertical Stacking Unit� � � � � � � � � � � � � � � � � � � � � � � � � � � 26

Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 28

Limited Warranty � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 32

Limited Warranty for Hermetic Compressors � � � � � � � 33

Limited Warranty Condensing Section � � � � � � � � � � � � 34

Limited Warranty for Hermetic Compressors � � � � � � � 35

Air-Cooled Unit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 36

Start-Up Procedures

(R-410a Systems)� � � � � � � � � � 36–37

Air-Cooled Unit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38

Start-Up Procedures � � � � � � � � � � � � � � � � � � � � � � � � � � 38

Cooling Mode� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39

Electrical� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39

Heating Mode (Optional) � � � � � � � � � � � � � � � � � � � � � � � 39

Water-Cooled Unit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 40

Start-Up Procedures

(R-410a Systems)� � � � � � � � � � � � � 40

Start-Up Procedures

(R-410a Systems)

Continued:� �41

Optional Heating Start Up: � � � � � � � � � � � � � � � � � � � � � � 41

Water-Cooled Unit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42

Start-Up Procedures � � � � � � � � � � � � � � � � � � � � � � � � � � 42

Cooling Mode� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43

Electrical� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43

Heating Mode (Optional) � � � � � � � � � � � � � � � � � � � � � � � 43

Basic Model Designation� � � � � � � � � � � � � � � � � � � � � � � � 44

Summary of Contents for C13-Series














































Search results

Summary of Contents for C13-Series

Reviews:

Related manuals for C13-Series

Brands by name

Popular brands

United cool air C13-Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for C13-Series

Reviews:

Related manuals for C13-Series

Brands by name

Popular brands