background image

6

FUNCTIONS OF DIGITAL DISPLAY,

CONTROL PANEL AND EMERGENCY STOP

OPERATION INSTRUCTIONS

2) Speed control

A)These can be used for increasing or decreasing speed

manually. The speed can be increased or decreased
by unit to 1 speed when these buttons are pressed.

B)The range of speed that can be adjusted manually is

speed 1-9.

SPEED SET

UP

DOWN

Speed control button

3) Forward, Reverse and Stop control

FWD

REV

STOP

Press FWD or REV or STOP button can change the
working condition of the machine.
A)Motor runs forward, the laminating film in, the

machine works.

B)Motor runs reverse, the laminating film out. This

function is used for remove the object inserted by
mistake.

C)Motor stop. This function is used for standby.

4) Function selection

HOT

COLD

SELECT

A)Press the SELECT button to change the function of

machine between hot and cold lamination.

B)While the HOT lamp is light, the machine is on hot

laminating.

C)While the COLD lamp is light, the machine is on

cold laminating.

3. Emergency Stop

There is a emergency stop button on the front of the
laminator. In emergency situation pressing the button
will stop the rollers and stop heating. Rotate the button
to the direction of arrow to turn on the power supply.

PREPARATION

1. Connecting the power source

3.Film threading
HOT FILM

Remark: the machine will power off when the safety shield and the feed

table are not in their proper positions.

1) Checking the rated voltage on the machine, to insure it conform to the power

source. Also, checking the plug to insure it conform to the socket.

2)

3)

Step 1: Raising the safety shield.

Remove the active bolt on the shield, raise the safety shield.

Step 2: Taking out the feed table.

Remove the active bolt under the feed table, take out the feed table.

Step 3: Follow the diagram to thread the film

Insert the plug into the power socket that is grounding correct.

Turn on the power switch, the display light, it indicates the power is connected.

This machine is equipped with motor overload circuit breaker (it is located next
to the power switch), in order to protect the motor working normally. When the
motor is overload, the circuit breaker will jump and cut off the motor power. One
minute later, when the overload is clear, press the circuit breaker button, the
motor will start again.

2. Motor overload circuit breaker

7

Film outside top
stabilizer bar

Top roll film

Top stabilizer bar

Top heating roller

Bottom roll film

Bottom stabilizer bar

Bottom heating roller

Top pull roller

Bottom pull roller

Film inside t op
st abilizer bar

Top roll film

Top stabilizer bar

Top heating roller

Bottom roll film

Bottom stabilizer bar

Bottom heating roller

Top pull roller

Bottom pull roller

POWER
SWITCH

WIRE

CIRCUIT
BREAKER

FAN
SWITCH

FAN

ON

OFF

POWER

ON

OFF

PDF 

文件使用

 "pdfFactory Pro" 

试用版本创建

  

 

 

 

 

 

 

 

 

 

www.fineprint.cn

Summary of Contents for LW-1100R









Reviews: