Don 't disjoin t, mo dify and repa ir the ma chine you rself .
If th ere a re a ny pr oble ms o n the machine, ple ase d o no t
use it,se nd it to th e dea ler f or re pair ing.
If the su pply cord is d ama ged, it must b e re plac ed b y
the ma nu fa cture r, i ts s ervic e a ge nt or simila rl y
qua lifie d per sons in o rder to av oid a haza rd.
12
Press FWD or REV button, the roller will run, cleans the roller. After
cleaning, position the feed table and slide on the safety shield.
No power is getting to the machine.
Make sure there is power at the electrical outlet being used, and
make sure both ends of the power cord are firmly engaged.
The laminator equipped with three fuses, they are located under the bottom of
laminator. Please check these fuses.
Wrinkling of the film around the material being laminated.
This is normal and inevitable on any laminator, especially with
thicker material. These wrinkles will be trimmed away with the scrap, so they do
not affect appearance. Because the rollers are being held apart by the paper, they
cannot pull equally on the plastic around the paper. This creates wrinkles that
tend to look like the bow waves of a boat, radiating out through the clear part of
the web from the sheet of material.
When two pieces of material are laminated side by side, the plastic
adhesive to one piece but not the other.
To get maximum efficiency from the film rolls, you can feed
several items into the laminator side by side. However, wrinkling can occur if
these items are of unequal thickness, because the laminating rollers are lifted off
the thinner items by the thicker items. When laminating items side by side, it is
important to arrange them so that the thickness is the same.
Film gets wrapped around the laminating rollers while hot
laminating.
The film is threaded improperly. If the adhesive side face to the
Caution: if the film gets wrapped around the roller, press STOP button
(stop heating) immediately. Warning: do not use any cleaning solution
to clean the roller, because some solutions may burn on the hot roller.
After the roller cool down, cut the film on the top and bottom, just in
front of the stabilizer bars. Reverse the roller at a very low speed and
allow the machine to back out the film that is wrapped around the rolls,
pull the film off the roller. Clean the adhesive on the roller.
Please read this section before you have a problem
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
PROBLEM SOLUTION
1
WARNING
Please do not use broken, aging or self-made electrical wire and damaged supply cord.
Please do not immoderately draw, twist or enlace the electrical wire, to avoid the fire or
electric shock.
Please do not use the power supply that is not in accordance with the rated voltage, to
avoid the fire or electric shock.
NO DISJO INT
ENTANGLEM ENT
CAUTION
ELECTRIC SHOCK
CAUTION
HIGH
TEMPERATURE
CAUTION
Kee p ha nds, long hair, loo se cl othi ng and ar ticle s lik e
ties or neck lace s aw ay from the rol lers to avoi d
enta ngle men t.
In case some arti cles enta ngle d, pr ess the
bu tton immediately; if no t wo rkab le, c ut o ff th e
power s upply at onc e, a nd c onta ct yo ur d ealer fo r
settleme nt.
E merg enc y
Sto p
Do not p ut ar ticle s on the lamin ator whil e it is working ,
so t hat to disp erse the heat.
Do not i nser t the easy -burnt or easy -sof tene d material
into the mach ine, in c ase they a re melt and g ive r ise t o
smo ke.
Do not t ouch the c ove r, heating roller and hea ting parts
whi le th e machin e is worki ng, in cas e he at injury.
Do not m ake the e lectrical wire or p lug or th e ma chin e
bed ewed by w ate r or o ther liquids.
Do not o pera te th e machine with we t han d.
Do not make the machine pre ssin g on the electrical
wire .
Do cut off the power s upply wh ile m ovin g the mac hine .
Do not o pera te th e machine with the cov er op en.
MAINTENANCE AND SERVICE
SAFETY PRECAUTIONS
文件使用
"pdfFactory Pro"
试用版本创建
www.fineprint.cn
