11
COLD LAMINATING
GENERAL MAINTENANCE
CLEANING THE RUBBER ROLLERS
1. Press the SELECT button until the COLD lamp is light, load the cold film.
2. Set the proper film tension by the top roll tension knob, set the speed at level 2
or 3.
3. Put the document on the feed table. Press the FWD button. The liner and film
will be rolled at the same time.
4. Stop the machine after the document to be laminated pass through the roller
completely, otherwise there will be an imprint on the document.
Do not laminate the metal or other hard items in case the damage of the rubber
rollers.
While stop the laminating, lift the top rubber roller with the knob on the right
side of the machine. Do not press the rubber roller in case the rubber become
stiff and thus shorten its work-life.
Cleaning the machine timely will help prevent dirt or adhesive build-up on the
rubber rollers and will improve the performance of the unit.
During the normal lamination, excess adhesives from the film will often cling to
the rubber rollers.
To clean the rubber rollers, lift the rubber roller, remove the film from the
machine first, heat up the machine to 30-40
. The warm roller enable it
easier to remove the adhesive built-up on the rollers. Raise the safety shield
and take out the feed table. Using a clean, soft, ethanol dampened cloth,
gently rub the adhesive off the rollers.
Caution: The adhesive side must face away from the roller.
Remind: The width of document should be larger than the width of cold
film. If the width of document is smaller than the width of cold film, please
put a protection paper under the document (the width of paper should be
larger than the width of cold film) .Otherwise, glue from the film will be
stuck on the face of roller and it can be seriously damaged.
Caution: Never use any abrasive or sharp metal material or rub too
hard on the roller, because you may damage the rubber surface.
℃
2
CAUTION
WORKI NG
PLACE
This mac hine should b e pu t at the dry an d cle an p lace, do not p ut it
at th e damp pl ace or ne ar the exi t of cooli ng applia nces.
This machine sho uld be p ut on the hor izon tal a nd fi rm place. In
fron t and rear of the mach ine, there sho uld be su ffici ent place for
the document in and ou t.
Do n ot put an y art icles on the machine.
LA MINATI NG
FILM
Plea se u se g ood quality laminatin g fil m, i n or der to s how the
lamination effect, and avoi d the enta ngle ment.
OB JECT
The lami nating machine us e the hot press tech nolo gy, do no t use the
followin g objects in case lam inati ng f ailure or lam inating f ilm
enta ngle .
. An y a r t ic l e s t h at h av e d r a pe, bre a ka g e, d am p ne s s o r
deformat ion before laminat ing.
4. Coin or a ny o ther hard artic les.
※
※
※
1. Easy -bur nt material, easy-s ofte ned mater ial
2. The documen t pri nted by heat- sensi tive paper, or any articles
that can be fa ded or tra nsfo rmed afte r heating .
3
Do not a ttempt to laminat e art icles tha t exc eed total rec omm end
material thickness .
m eans exceptio n while c old laminating opera tion.
MACHI NE
OP ERATION
Do not turn t o other usages ex cept the usag e range state d in this
operation manual.
Do n ot use the machine out side the r oom. Bef ore leaving, p lease cut
off the power supp ly if the operation is over.
Read all safet y me ssag es locate d in this manu al and on the machine
very care fully.
While opera ting the mach ine, mind the children nearby, in case any suddenn ess.
Do not suspend the electrical wire on the table or cabin et or any othe r places
tha t the children can touch, or plac e eas y stu mble per sons .
Us ing t he a ccessory that not r ecommended or sold b y the ma nufa cture r, might
cause d amage on the machine.
Th e ph oto or do cument once is la mina ted, it will becom e pe rmanent and will
no t be t aken apart.
Please do n ot lamin ate t he c ollected rare artic les, or some articles migh t be
tak en o ut in the future.
ADVICES
SAFETY PRECAUTIONS
MAINTENANCE AND SERVICE
文件使用
"pdfFactory Pro"
试用版本创建
www.fineprint.cn