Page 11
P O W E R I N G T E C H N O L O G Y
Manual No. sli-15-G-3a
sli15-userguide-rev3a-0718.indd
Set Remote ON/OFF
Remote ON/OFF - - >
1.9
ON/OFF
1.9.1
-
Remote ON
⇒
It is possible to turn ON /OFF the unit
remotely provided that a switch or relay is connected
between pins 6 and 7 of the signal connector on the back
side of the unit. Refer to the Installation Manual".
-
Factory Setting: Remote "OFF"
<ENT>
Set Autostart Mode
Autostart
- - >
1.8
Autostart ON/OFF
1.8.1
-
Auto-Start ON
⇒
the unit starts up as soon as the DC input
source connection is made. In this case there is no need to
press the <ON/OFF> key on front panel.
-
Auto-Start OFF
⇒
The unit starts up only after <ON/OFF> key
has been pressed.
-
Factory setting: Auto-Start OFF
Set New Password
Password ****
1.11.1
-
This option allows to change the current password. To set the
new password digits use the <UP> and <DOWN> keys.
-
Max. Password length: 4
-
Factory setting: "0000"
New Password - - >
1.11
<ENT>
NOTES
The following settings are not accessible when the current configuration unit mode is the
Parallel mode.
That is to avoid conflicts within the system. Set Vout , Set I
LIMIT
, Set Frequency, Set Remote ON/OFF.
If the user wants to make changes when operating in Parallel mode, he unit must first of all set to Stand-
Alone mode using the following procedure (to be repeated for each unit working in parallel):
1. Set the unit to Stand-alone mode:
•
on the SETTINGS menu select the SERVICE submenu. Press <Enter> to confirm the choice.
•
Insert the 2nd level password (default password is “1111”; use the <UP> and <DOWN> keys to select
the digits. Press <Enter> to confirm.
•
Select the OPERATING MODE submenu and press <Enter>.
•
Change "Mode = 2"(parallel mode) into "Mode =0"(stand-alone mode). Use the <UP> key to insert the
character "0".
2. Change the Vout, I
LIMIT
, Frequency and Remote ON/OFF settings like explained before.
3. After the changes are done restore the parallel mode with the same procedure described in step 1.
It is strongly recommended to set all units with identical Vout, I
LIMIT
, Frequency and Remote ON/OFF values
when working in parallel.
Set Remote ON/OFF
Remote ON/OFF - - >
1.9
ON/OFF
1.9.1
-
Remote ON
⇒
It is possible to turn ON /OFF the unit
remotely provided that a switch or relay is connected
between pins 6 and 7 of the signal connector on the back
side of the unit. Refer to the Installation Manual".
-
Factory Setting: Remote "OFF"
<ENT>
Set Autostart Mode
Autostart
- - >
1.8
Autostart ON/OFF
1.8.1
-
Auto-Start ON
⇒
the unit starts up as soon as the DC input
source connection is made. In this case there is no need to
press the <ON/OFF> key on front panel.
-
Auto-Start OFF
⇒
The unit starts up only after <ON/OFF> key
has been pressed.
-
Factory setting: Auto-Start OFF
Set New Password
Password ****
1.11.1
-
This option allows to change the current password. To set the
new password digits use the <UP> and <DOWN> keys.
-
Max. Password length: 4
-
Factory setting: "0000"
New Password - - >
1.11
<ENT>
NOTES
The following settings are not accessible when the current configuration unit mode is the
Parallel mode.
That is to avoid conflicts within the system. Set Vout , Set I
LIMIT
, Set Frequency, Set Remote ON/OFF.
If the user wants to make changes when operating in Parallel mode, he unit must first of all set to Stand-
Alone mode using the following procedure (to be repeated for each unit working in parallel):
1. Set the unit to Stand-alone mode:
•
on the SETTINGS menu select the SERVICE submenu. Press <Enter> to confirm the choice.
•
Insert the 2nd level password (default password is “1111”; use the <UP> and <DOWN> keys to select
the digits. Press <Enter> to confirm.
•
Select the OPERATING MODE submenu and press <Enter>.
•
Change "Mode = 2"(parallel mode) into "Mode =0"(stand-alone mode). Use the <UP> key to insert the
character "0".
2. Change the Vout, I
LIMIT
, Frequency and Remote ON/OFF settings like explained before.
3. After the changes are done restore the parallel mode with the same procedure described in step 1.
It is strongly recommended to set all units with identical Vout, I
LIMIT
, Frequency and Remote ON/OFF values
when working in parallel.