background image

 

 

19 

 

8. Maintenance 

 

1. 

DO a regular battery checkup and recharge it fully before use whenever the battery is low. 

2. 

Perform the calibration check once in a month. Calibration check  every month will ensure 

the accuracy of readings throughout the life of the instrument.

 

3. 

NEVER allow the unit to be used in direct sunlight. You may provide the canopy/sun shade 

while using the instrument on the site.

 

4. 

ZERO it in a target gas-free clean air. 

 

5. 

NEVER expose the sensor to gas concentration higher than its prescribed range.

 

6. 

DO  NOT  expose  the  monitor  to  excessive  positive  or  negative  pressure.  It  affects  the 

accuracy of the measurement.

 

7. 

Occasionally,  the  casing  of  the  instrument  can  be  cleaned  with  a  slightly  damp  lint  free 

cloth. Wipe  the  instrument  thoroughly  dry  using a fresh  lint  free  cloth.  But  care  should  be 

taken not to allow any water or moisture to enter the instrument.

 

8. 

Do not keep the monitor without use, for more than 3 months (from the date of 
shipment). Li-Ion battery performance may get affected. 

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for FumiSense Pro UNIPHOS-250


























Reviews: