Unimig RAZOR 320 AC/DC, Operating Manual

Page: 19 / 48

Test
ADJUSTMENT
Ignition
Time
Ignition AMP
AMP Set
Arc Force
AC
Hz
Hz
Pulse
Mix
SPOT
%
ON OFF
AC Balance
Start
Amp
Peak
Amp
Base
Amp
Spot
Finish
Amp
JOB #
SELECT
AC
WAVE
TORCH
MODE
LIFT ARC
PULSE
REMOTE
WATER
JOB #
SAVE
JOB #
RECALL
DELETE
MMA
TIG
MMA
HF
2T
4T
4S
SPOT (DC)
(AC)
(Mix)
ON
ON
DC
AC
Test
ADJUSTMENT
Ignition
Time
Ignition AMP
AMP Set
Arc Force
AC
Hz
Hz
Pulse
Mix
SPOT
%
ON OFF
AC Balance
Start
Amp
Peak
Amp
Base
Amp
Spot
Finish
Amp
JOB #
SELECT
AC
WAVE
TORCH
MODE
LIFT ARC
PULSE
REMOTE
WATER
JOB #
SAVE
JOB #
RECALL
DELETE
MMA
TIG
MMA
HF
2T
4T
4S
SPOT
(DC)
(AC)
(Mix)
ON
ON
DC
AC
Test
ADJUSTMENT
Ignition
Time
Ignition AMP
AMP Set
Arc Force
AC
Hz
Hz
Pulse
Mix
SPOT
%
ON OFF
AC Balance
Start
Amp
Peak
Amp
Base
Amp
Spot
Finish
Amp
JOB #
SELECT
AC
WAVE
TORCH
MODE
LIFT ARC
PULSE
REMOTE
WATER
JOB #
SAVE
JOB #
RECALL
DELETE
MMA
TIG
MMA
HF
2T
4T
4S
SPOT (DC)
(AC)
(Mix)
ON
ON
DC
AC
Test
ADJUSTMENT
Ignition
Time
Ignition AMP
AMP Set
Arc Force
AC
Hz
Hz
Pulse
Mix
SPOT
%
ON OFF
AC Balance
Start
Amp
Peak
Amp
Base
Amp
Spot
Finish
Amp
JOB #
SELECT
AC
WAVE
TORCH
MODE
LIFT ARC
PULSE
REMOTE
WATER
JOB #
SAVE
JOB #
RECALL
DELETE
MMA
TIG
MMA
HF
2T
4T
4S
SPOT (DC)
(AC)
(Mix)
ON
ON
DC
AC
Test
ADJUSTMENT
Ignition
Time
Ignition AMP
AMP Set
Arc Force
AC
Hz
Hz
Pulse
Mix
SPOT
%
ON OFF
AC Balance
Start
Amp
Peak
Amp
Base
Amp
Spot
Finish
Amp
JOB #
SELECT
AC
WAVE
TORCH
MODE
LIFT ARC
PULSE
REMOTE
WATER
JOB #
SAVE
JOB #
RECALL
DELETE
MMA
TIG
MMA
HF
2T
4T
4S
SPOT
(DC)
(AC)
(Mix)
ON
ON
DC
AC
Remote Mode Selector
Provides selection selection of the type of Remote Control to be use as required,
including remote torch potentiometers and foot controls.
•
Torch Ignition
• Remote Foot Pedal / Torch Ignition
Saved JOB System
Allows the operator to save the set welding parameters and asign them to a
JOB number. The JOB number can be recalled later as required, the welding
parameters are preserved inside the JOB number ready for use.
1. JOB SELECT
Use the JOB SELECT (+) and TEST (-) buttons to cycle through the JOB numbers.
2. JOB SAVE
Press the JOB SAVE button to save the current settings to the selected JOB number.
3. JOB RECALL
Select the desired JOB NUMBER, then press the JOB RECALL button to load
saved settings.
4. JOB DELETE
Select the desired JOB NUMBER, then hold the JOB RECALL button for 2s to
delete saved settings.
Water Cooler Mode
Provides electronic link when water cooler unit is connected to the machine
• Press button to turn
ON / OFF
GAS TEST
Press the GAS TEST button to initiate a gas test. After 20s the test will end, you
can also end the test by pressing the GAS TEST button again.
Water Cooler Connection
The water cooler is connected to the power source via a 5 Pin connector located
at the rear of the machine. The connector provides 220-230VAC power supply
to the water cooler unit via Pins 1&2. The machine will monitor the water flow and
welding off time via a signal circuit connected to Pins 3&4.
NOTE: This sensor circuit will turn off the welding output should there be no
or insufficent water flow from the water cooler unit. This will prevent the Water
Cooled torch cable from over heating and burning out.
When using RAZOR 320 AC/DC machine with a Water Cooled TIG Torch ensure:
1.
The water cooler is plugged into the power supply at the rear of the Power Source.
2. The water level is to the full level.
3. The water cooler is switched on using the on/off switch located on the front
panel of the water cooler.
4. The power source is in Water Cooler Mode by selecting the Water On icon on
the front panel.
TIG CONTROL PANEL OPERATION
19