Unifire SUPERVISOR I Installation And Operation Manual Download Page 17 | Manualshive

Page: 17 / 22

Unifire SUPERVISOR I Installation And Operation Manual Download Page 17

0014_Installation_Operation_Manual

A0

support@unifire.ca

Copyright 2017 Unifire

6.

On conclusion of the PURGE the
STANDBY/PURGE LED switches OFF and
the trial for ignition begins. The FLAME
LED flashes. The Ignition (IGN) output
and DO1 driver are energized.

FR

IGN

DO1

DO2

DO3

7.

Once a flame is detected the FLAME
LED is held ON and the Ignition (IGN)
output is de-energized.

FR

IGN

DO1

DO2

DO3

8.

On expiry of the flame stable timer the
DO2  and  DO3  outputs  are  Energized.
The  system  now  monitors  for  flame
continuously  until  STANDBY/RESET  is
pressed or power is removed.

FR

IGN

DO1

DO2

DO3

9.2

Interrupted Pilot

1.

With FAULT and FLAME OFF the system
can  be  started  by  pressing  the
START/RESET  button.  The  PURGE
commences  with  the  STANDBY/PURGE
LED flashing.

FR

IGN

DO1

DO2

DO3

2.

Press START/RESET at any time to reset
the system. STANDBY/PURGE stops
flashing.

FR

IGN

DO1

DO2

DO3

«
...
15
16
17
18
19
...
»

Summary of Contents for SUPERVISOR I























Reviews:

No comments