Uniden XDECT R003 Owner'S Manual Download Page 7

7

Picking the best spot

The best spot for the repeater/ 

charger is as far from the 

base as possible while still 

maintaining a good signal, 

or near the edge of the 

base’s coverage area1 To 

find the edge of the 

coverage area:

Stand near the base 

11 

and make a call on the 

handset1
While on the call, carry 

21 

the handset away 

from the base towards the general area where you want to put the 

charger1 
Watch the signal strength icon on the handset1 Make a note where 

31 

the icon drops from 4 bars to 3 bars1
Continue walking away from the base1 Make a note where the signal 

41 

strength icon drops from 3 bars to 2 or if you start to hear noise on 

the line (which indicates the signal is getting weaker)1
Place the charger anywhere inside the range where the signal 

51 

strength icon showed 3 bars and the handset had a clear signal with 

no noise1 

Testing the location

Connect the charger's AC adapter and make sure the 

lINk

 light 

comes on steadily1 If the light flashes, the repeater/charger is not 

getting a good signal from the base1 The charger may be too far 

away from the base, there may be interference from electronic 

devices, or the signal might be blocked by thick walls or metal 

objects1 Try moving the charger to another location1

Summary of Contents for XDECT R003













Reviews: