Uniden EXP1240 Installation Manual Download Page 42

Page: 42 / 71

EXP1240 System Installation Guide

Revision 06

PROPRIETARY AND CONFIDENTIAL

Page 42 of 71

Valid server, folder, and firmware file name examples (handsets)

•

tftp://update.abc.com/ipdect/firmware/Pegasus/PegasusSW_4181_v0019.fwu

•

tftp://abc.com/firmware_update/Pegasus/PegasusSW_4181_v0007.fwu

•

tftp://192.168.10.207/fwupdate/Pegasus/PegasusSW_4181_v0023.fwu

Configuring the Firmware Update Settings

Firmware Update

screen.

Figure 30:

Firmware Update

server information

In the

Firmware update server address

field, enter the name or IP address of the TFTP

server.

∘

Enter the folder path between the server root and the Beatus or Pegasus
folder.

∘

Do not include the folder name for base stations (

Beatus

) or handsets or

(

Pegasus

): these are added automatically).

∘

This field must start with a forward slash (/).

∘

Do not include a forward slash at the end of the field.

∘

The table below shows how you would enter the server address and
firmware path using the examples shown on page 41.

Table 7 Firmware path examples

Firmware update

server address

Firmware path

Firmware

folder

Firmware file name

Base station firmware files

update.abc.com

/ipdect/firmware

/Beatus/

BeatusSW_4181_v0026.fwu

abc.com

/firmware_update

/Beatus/

BeatusSW_4181_v0001.fwu

192.168.10.207

/FWupdate

/Beatus/

BeatusSW_4181_v0127.fwu

Summary of Contents for EXP1240








































































Search results

Summary of Contents for EXP1240

Reviews:

Related manuals for EXP1240

Brands by name

Popular brands

Uniden EXP1240, Installation Manual

Search results

Summary of Contents for EXP1240

Reviews:

Related manuals for EXP1240

Brands by name

Popular brands