Unicum AN1244 User And Installation Manual Download Page 2

User and installation manual  

 

Réf : 004057-02

 

 

Page : 2/17 

 

Important security instructions 

 

 

 

WARNING 

Swimming pool can represent a major danger for your children. Drowning can happen 
very suddenly and quickly. You must actively survey any children using the swimming 
pool even if they can swim. Physical presence of an adult person is mandatory when a 
pool is open. 
 

 

 

 

 

WARNING 

Please check carefully that none and no object is inside the swimming pool before and while operating the cover. 

 

 

 

WARNING 

Keep away from children any device that may operate the cover (key, remotes, etc) . 
Cover operation must me done by an adult person.

 

 

 

PLEASE FOLLOW CAREFULLY ALL INSTRUCTIONS 

 

 

 

WARNING

 

FOR YOUR SECURITY – Product installation must be performed by a qualified and authorized technician who 
has been trained to swimming pool equipment installation. Before installing this product, please read the whole 
user manual and follow all instructions paying particular attention to warnings that may prevent product failure 
or other material damages. Any improper installation or usage of the control box will make the warranty void. 

Electric wiring and connection to mains network MUST be done following applicable security norms. 

An improper installation or usage may create an undesired electrical danger which could cause material or 
personnel damages. 

 

 

WARNING

 

FOR INSTALLATION TECHNICIANS: this guide contains important information concerning installation, usage 
and security recommendations that must be communicated to the final user. Not learning and applying these 
instructions may cause important material damages and injuries or even death. 

Summary of Contents for AN1244


















Reviews: