Unico MCV85 TOTAL CLEAN & TURBO, Instruction Manual

Page: 32 / 116

1. PREPARATION FOR SUCTION FUNCTION USE
(Chart Page 2)
1.1 Insert the vacuum tube into the body of the appliance.
1.2 Lock the telescopic tube to the handle and adjust to the
desired height.
1.3 Connect the Multibrush brush to the telescopic tube.
Tips: To facilitate the following operations, lock the brush to the
parking system.
1.4 Completely unwind the power cable and connect it to an
appropriate mains socket (1). Always use the product with the
cable completely unwound.
1.5 Switch on the appliance by pressing the power switch. The
indicator light next to it will come on. The appliance is ready for
use. To start the suction, press the vacuum button on the control
panel (3).
1.6 It is possible to adjust the suction power by moving the
cursor on the handle (4).
1.7 Unico can be used with the FrescoAspira air freshener tabs.
Based on natural essences, it releases a pleasant fragrance
during the suction operations. Refer to Chapter 26 for the use of
FrescoAspira.
2. PREPARATION FOR STEAM USE
(Chart Page 2)
2.1 Lock the steam hose to the vacuum tube, then insert them
to the body of the appliance, making sure that the two
connectors at the ends of the vacuum tube are connected.
Without the steam hose, it is impossible to activate the steam,
even with the boiler switched on.
2.2 To connect the machine side steam hose, lower the steam
attachment door and insert the steam connectors, sliding it into
position until you hear a click as it locks into place (diagram
page 2 - F).
2.3 Open the door of the tank and fill it with water, taking care
that it does not overflow (10). Close the door.
This operation must always be carried out with the power cable
disconnected from the mains.
Thanks to the self-filling system, it is not necessary to wait for the
appliance to cool before refilling the boiler with water.
When the water in the water tank runs out, the “Out of water”
indicator light will light up on the control panel (tap symbol) and
you will hear a beep.
To continue use, it is sufficient to refill the tank.
2.4 Completely unwind the power cable and connect it to an
appropriate mains socket. Always use the product with the
cable completely unwound.
2.5 Switch on the appliance by pressing the power switch (2). The
indicator light next to it will come on. The appliance is ready for
use. To use steam, switch on the boiler by pressing the ON (12)
button and adjust the steam depending on the surface to be
treated as detailed in Chapter 4.
2.6 When the boiler is turned on, the steam indicator light flashes:
the boiler is heating up. When the indicator light is constant, after
around 5 minutes (13) the appliance is ready for steam function
use.
2.7 The handle has a safety button which prevents involuntary
activation and accidental steam delivery (14). Should the
appliance be left momentarily unguarded when the appliance
is activated, move the safety button to the “steam lock” position
(14-A). To resume delivery, move the button to the initial
position (14-B) and press the steam trigger on the handle (15).
3. PREPARATION FOR USE OF COMBINED
STEAM / SUCTION FUNCTION
The steam and suction functions can be used at the same time
to wash and sanitise the surfaces and then dry them. For the
combined function, prepare the product as described in Chap-
ters 1 and 2.
4. STEAM ADJUSTMENT
It is possible to adjust the intensity of the steam using the
+/buttons. (16). Here are some tips for regulating it:
• Maximum level: for resistant floors and surfaces, to remove
limescale, stains and grease;
• Medium level: to clean windows, floors and clean and bri-
ghten rugs and carpet;
• Minimum level: to clean parquet and laminate, delicate fa-
brics, upholstery, sofas and mattresses, etc. and to steam
plants.
WARNING: The level of dirt vacuumed should not exceed the
MAX indicator on the dirt collector; this indicator refers to both
solid and damp dirt (9). Upon reaching the maximum level, see
Chapter 17.
We recommend using the accessories holder, to be attached
to the appliance (7) or directly to the push/pull handle (8), to
have the accessories close at hand during the cleaning
operations.
We recommend using the special push/pull handle to move
the appliance more easily during cleaning operations (5-6).
Do not use the push/pull handle to lift the appliance.
We recommend using the special push/pull handle to move
the appliance more easily during cleaning operations. Do not
use the push/pull handle to lift the appliance.
We recommend using the accessories holder, to be attached
to the appliance (7) or directly to the push/pull handle (8), to
have the accessories close at hand during the cleaning
operations.
WARNING: When first operating steam, there may be some
drops of water mixed with the steam due to temperature
imbalances.
Direct the first jet of steam onto a rag.
| 32 |
ENGLISH
UNICO MCV80-MCV85 - M0S11431 - 1Q09:UNICO 30/08/2016 16.17 Pagina 32