Unical AIREX 150 Installation And Maintenance Instructions Manual Download | Manualshive

Page: 29 / 52

background image

Installation instructions

29

System with AIREX boiler and DOMESTIC HOT WATER immersion and coil STORAGE TANK with SOLAR
PANELS.

Production of water for central heating system with temperature control by means of manual mixer valve (or electric
managed by supplementary heating controller).

fig. 26

When a “COMBI” type heater is installed which is mainly an
storage tank, aside from the probes

S4

and

S5

, probes

S2

and

S3

must be enabled as well.

For the storage tank pump (

Pb

) to work, the boiler water

temperature detected by the probe

S4

must be greater than the

minimum temperature set on

PARAMETER 1

.

Furthermore, the storage tank is loaded if the boiler temperature
(probe

S4

) is higher than the temperature detected on the lower

part of the storage tank (probe

S2

) plus

PARAMETER 6

(storage

tank loading thermal delta).
When the temperature of the storage tank drops below the mi-
nimum value set on

PARAMETER 3

, the program automatically

activates the domestic hot water priority.

With this type of configuration, operation of the system pump is
no longer linked to boiler water temperature but to the minimum
storage tank temperature measured by probe

S3

.

Therefore if the combi storage tank is at a higher temperature
than the minimum set temperature (PARAMETER 3), the system
pump will be activated on demand by the room thermostat even
if the boiler is cold.
As for operation of the boiler recirculation pump and of the solar
panel loading pump, it is the same as described on page 26.
This type of system also requires installation of an anti-
condensation recirculation pump.

CALDAIA A LEGNA

Pr

VE

S4

S5

IR

VM

Pi

TAS

SONDA

FUMI

S1

Ps

VE1

CS

Pb

SCAMBIATORE AD

ACCUMULO

(TANK in TANK)

S3

S2

KEY:
Pr
VM
Pi
Pb
Ps
VE
VE1
IR
TAS
CS
S1
S2
S3
S4
S5
TKS
TA
FLUE GAS PROBE

recirculation pump (if not installed, the warranty is null and void)
manual zone mixer valve (or electric, managed by supplementary heating controller)
heating system pump
storage tank loading pump
solar heat exchanger pump
open expansion vessel
closed expansion vessel
heating system distribution (loading)
thermal discharge valve probe
solar heat exchanger
solar heat exchanger probe
storage tank bottom probe
storage tank top probe
flow temperature probe
return temperature probe
door opening microswitch
room thermostat or chronothermostat
flue gas temperature probe

=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=

WOOD BOILER

STORAGE TANK
HEAT EXCHANGER
(TANK in TANK)

FLUE GAS
PROBE

«
...
27
28
29
30
31
...
»

Summary of Contents for AIREX 150





















































Reviews:

No comments

Related manuals for AIREX 150

Brand: Bakers Pride Pages: 18

Brand: Ravenheat Pages: 56

Brand: Unical Pages: 46

Rotex A1 BO Series

Brand: Daikin Pages: 60

Brand: IBC Pages: 78

Brand: Alpha Pages: 5

Brand: Buderus Pages: 8

Brand: Alpha Boilers Pages: 32

Cantinola Touch Series

Brand: Pasqualicchio Pages: 43

Brand: Lang Pages: 17

Cleveland 24CGP10

Brand: Welbilt Pages: 42

Brand: Navien Pages: 29

Expansion module 1

Brand: Thermia Pages: 28

Brand: Unical Pages: 48

Logano plus SB315

Brand: Buderus Pages: 16

Brand: Ponast Pages: 59

Brand: Bonnet Pages: 37

Brand: Immergas Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands