background image

Installation instructions

11

3

INSTALLATION 
INSTRUCTIONS

3.1 - GENERAL WARNINGS

ATTENTION!
This boiler is intended solely for the use for 
which it was expressly designed. 
Any other use is to be considered improper 
and therefore dangerous.
This boiler heats water at a temperature 
lower than the atmospheric pressure boiling 
temperature.

ATTENTION! 
The appliances are designed to be installed 
inside suitable rooms or technical spaces 
only. The appliances cannot be installed or 
operate outdoors. Outdoor installation can 
cause malfunctioning and be dangerous. 
Choose specifically designed appliances for 
outdoor installation.

Before connecting the boiler, have professionally 
qualified personnel:
a)  Thoroughly wash all the piping of the system 

to remove any residue or impurities which 
could jeopardise proper operation of the boi-
ler.

b)  Check that the chimney/flue has an appropriate 

draught, without any bottlenecks, and that no 
exhausts from other appliances are inserted, 
unless the flue has been implemented to 
accommodate several utilities according to 
specific standards and prescriptions in force. 
Only after this check can the fitting between 
the boiler and chimney/flue be mounted.

ATTENTION!

The appliance must be installed by a qualified 
technician with the technical-professional 
requirements according to law, which 
under his own responsibility, guarantees 
compliance with standards according to 
good practice rules.

The boiler must be connected to a central heating 
system and/or domestic hot water production 
network compatible with its efficiency and output.

Summary of Contents for AIREX 150





















































Reviews: