manualshive.com logo in svg

Unibloc-Pump LABTOP 200, Operation And Service Manual

Share
Download
Unibloc-Pump LABTOP 200 Operation And Service Manual Download Page 35

            

        Page 36 of 4

 

Function Keys 
 
F1

 Function Key

 Emergency Stop 

F2

 Function Key

  Home Screen (Figure 7.4.2.1) 

F3

 Function Key

 Non-Functioning 

F4

 Function Key

  Factory Settings.  Password Protected. 

SYS

 Key

 

System Settings.  Password Protected Code 12345678 (Figure 7.4.2.6) 

 

 

Figure 7.4.2.6 

 

7.4.3 Controller Settings and Update 

 
Adjustments may be made to the inverter which operates the function of the motor.  For detailed instructions on Parameter 
adjustments, please refer to Control Panel Manufacturers Operation Manual.  

Distribution of the access codes will void the 

warranty.

  

 
For units with Touch Screen Key Pad, 

REGISTER UNIT 

through factory for regular software updates.  Factory will provide 

formatted, FAT32 format, USB stick with updated software.  To update, press + hold SYS key in Figure 7.4.2.1.  On numeric 
keypad, type code 12345678 to enter System Screen in Figure 7.4.2.6.  Insert USB into panel on side of canopy and press Run on 
keypad.  Software will automatically update and restart unit.  Once unit has restarted, remove USB from side panel. 
 

7.4.4 Remote Operation 

 
The speed of the 

LABTOP

®

 unit may be changed from a remote location by using the 4-20mA input connection found on the rear 

side of the unit.  This is an optional feature that does not come standard on all units.  Please contact Flowtech for further details.  
If the unit has been supplied  with  this option then all that is required is to connect your 4-20mA device to the connection on the 
rear side of the unit.  The unit has been preprogrammed so that the maximum speed will be produced at the maximum input, 
20mA.  To begin  operation, energize your device, then  press FWD or REV on the keypad.    

Summary of Contents for LABTOP 200










































Reviews:

No comments

Brands by name

Popular brands

Load more brands