manualshive.com logo in svg

Unibloc-Pump LABTOP 200, Operation And Service Manual

Share
Download
Unibloc-Pump LABTOP 200 Operation And Service Manual Download Page 3

  Page 4 of 4

 

5.0 Technical Data ............................................................................................................................................ 27

 

5.1 General Dimensions and Weights ..................................................................................................................... 27

 

5.2 Lubricants and Bearing housing Oil Specification .......................................................................................... 27

 

5.3 Tools and Torque Requirements ....................................................................................................................... 29

 

5.3.1 Special Tools ....................................................................................................................................................................... 29

 

5.4 Rotor Clearances ................................................................................................................................................ 29

 

6.0 Pump Identification and Spare Parts ......................................................................................................... 30

 

6.1 Pump Identification ............................................................................................................................................ 30

 

7.0 Electronics/Operation ................................................................................................................................. 31

 

7.1 Input Voltage ....................................................................................................................................................... 31

 

7.2 Ventilation ........................................................................................................................................................... 31

 

7.3 Fuse Replacement ............................................................................................................................................... 31

 

7.4 Unit Operation .................................................................................................................................................... 32

 

7.4.1 Digital Key Pad Operation ................................................................................................................................................... 33

 

7.4.2 Touch Screen Key Pad Operation ........................................................................................................................................ 33

 

7.4.3 Controller Settings and Update ............................................................................................................................................ 36

 

7.4.4 Remote Operation ................................................................................................................................................................ 36

 

8.0 Warranty ...................................................................................................................................................... 41

 

PLEASE REGISTER YOUR LABTOP TO RECEIVE UP-TO-DATE SOFTWARE FOR CONTROLLER. 

REGISTRATION CAN BE DONE WITH ENCLOSED FORM OR FROM OUR WEBSITE 
WWW.

81,%/2&3803

.COM 

LABTOP SIZE:________________ 

PUMP S.N.: _________________ 

VFD S.N.:__________________ 

Summary of Contents for LABTOP 200










































Reviews:

No comments

Brands by name

Popular brands

Load more brands