manualshive.com logo in svg

Unibloc-Pump LABTOP 200, Operation And Service Manual

Share
Download
Unibloc-Pump LABTOP 200 Operation And Service Manual Download Page 16

            

        Page 17 of 4

 

 

4.4.1.3 UNIBLOC 300-450 Single Mechanical Seal Removal 

 
Loosen the 

Stud Nuts (item 43 in Figure 4.4.1)

.  Remove the 

Rotor Housing 

by pulling on the ports or by tapping gently with a 

rubber mallet. Do not rock the Rotor Housing back and forth excessively.  The seals may break. The 

Seal Retaining Rings

, the 

Bolts

, the 

Stationary Seal Faces

, and the 

Stationary Seal O-Rings

 will all come off with the Rotor Housing. Unscrew the 

Bolts 

to remove the 

Seal

 

Retaining Rings

, the 

Stationary Seal Faces

, and the 

Stationary Seal O-Rings

. Slide the 

Rotating Seal 

Faces

 and the 

Rotating Seal O-Rings

 off the shafts.  To avoid damage, handle and store the loose 

Stationary Seal Faces

 and 

Rotating Seal Faces

 so that their lapped sealing surfaces do not get scratched.  If not being replaced, the 

Drive Collars

 may 

remain on the shafts, otherwise loosen the set screws and slide them off the shafts.  UNIBLOC-PD 500 Series may use wear 
sleeves, See section 4.4.4.1 sketch. 
 

 

4.4.1.4 UNIBLOC 300-450 Single Mechanical Seal Installation 

 
The shafts and the rotor housing bores should be cleaned before installing the seal components.  Slide the 

Drive Collars

 on the 

shafts. Moisten the 

Rotating Seal O-Rings

 with water or coat them with a lubricant that is acceptable for use with the product. 

Slide the 

Rotating Seal O-Rings

 onto the shafts and then the Rotating Seal Faces, slotted sides first. Align the slots in the 

Rotating Seal Faces

 with the pins in the 

Drive Collars

. Push the 

Rotating Seal Faces

 against the 

Drive Collars

 so that the 

Rotating Seal O-Rings

 seat properly. Place the 

Stationary Seal O-Rings (front & outer) 

on the 

Stationary Seal Faces

.  Only 

lubricate these o-rings with water or alcohol. Push the 

Stationary Seal Faces

 into the rotor housing so that they seat flat with the 

step in the housing.  Some applications require pins to be used in the 

Stationary Seal Faces

.  When placing them in the rotor 

housing align the pins with the holes in the rotor housing and press them in.  Do not use objects that will scratch the 

Stationary 

Seal Faces

’ seal surface to push them in. Place a product compatible lubricant on the sealing surfaces. If 

Seal Retaining Rings

 

were supplied with the pump, bolt them to the rotor housing. 

Proceed to section 4.4.7 to complete the installation

.  After 

installing the housing push the 

Drive Collars

 toward it.  Compress the 

Wave Springs

 while leaving a 2-3mm (0.08”-0.12”) gap 

between the 

Drive Collars

 and the 

Rotating Seal Faces

. Tighten the Drive Collar set screws.  

 
 
 

 
 
 
 

UNIBLOC-PD 300-450 with Single Mechanical Seals 

Summary of Contents for LABTOP 200










































Reviews:

No comments

Brands by name

Popular brands

Load more brands