UNI-T UTL8500 Series User Manual Download Page 8

Page: 8 / 53

UTL8500 Series User Manual

1. Product Description

Thank you for purchasing the Uni-Trend Programmable DC electronic load. This chapter

mainly covers the following:



Product Series



Front Panel



Rear Panel

1.1 Product Series

UTL8500 series DC electronic load contains 4 models: UTL8511, UTL8512, U

and UTL8513.

Models

Measurement Range

Voltage

Current

Power

UTL8511

0~150V

0~30A

0~150W

UTL8512

0~150V

0~30A

0~300W

0~500V

0~15A

0~300W

UTL8513

0~150V

0~120A

0~600W

UTL8500 series DC electronic load comes with 4.3-inch LCD screen, wide power range

and up to 0.1mV/0.1mA resolution. It supports multiple test modes: dynamic test, overload

test, auto test, list test, battery test and CR-LED test, etc. The instrument is great tools in

areas of electronic performance test, battery set test, power supply test, new energy test,

aerospace industries, high-power test, labs, R&D and production line, etc.

Equipped with standard RS232 interface and support more extension interfaces, UTL8500

series offer multiple-role solutions for your different design and testing requirements.

1.1.1 Features



Measurement Range: 150W/300W/600W,150V/500V,15A/30A/120A



Four Basic Test Modes: CC/CV/CR/CP



Function of Remote Current Monitoring and External Triggering



High Resolution of 0.1mV/0.1mA



Dynamic Voltage/Current Test with up to 10k Dynamic Frequency



Voltage/Current Sampling Rate: 40kHz



CR-LED Test, Power Source Rise/Decline Time Test



Protections of Over-Voltage/ Under-Voltage/ Over-Current/ Over-Power/ Overheat/

Anti- Reverse Connection

Summary of Contents for UTL8500 Series






















































Search results

Summary of Contents for UTL8500 Series

Reviews:

Related manuals for UTL8500 Series

Brands by name

Popular brands

UNI-T UTL8500 Series, User Manual

Search results

Summary of Contents for UTL8500 Series

Reviews:

Related manuals for UTL8500 Series

Brands by name

Popular brands