UNI-T UTL8500 Series User Manual Download Page 4

Page: 4 / 53

UTL8500 Series User Manual

to the user, be sure to use this product in accordance with the regulations.

Please read through the safety guideline, in case the meter is not used properly as

instructions, the protection provided may be weakened or lost.

Correct connection of ground wire

: To avoid electric shock, please use the provided

cable to connect and make sure that the product is properly grounded before use.

Please notice the rated operating range.

Please ensure that the mains supply does not

exceed 10% of rated operating range to prevent damage.

Use the correct power line:

Only use the dedicated UNI-T power line to connect the

measured power supply and the electronic load, which is to ensure that there is no overheat

by short-circuit current, otherwise electric shock may occur.

Please notice the product marks before connecting.

The instrument supports 2 kinds

of AC input method: 110V and 220V. Please check if the switch of load is match with the

input power source, and the fuse is correctly installed, or damage will occur.

Please do not operate in inflammable and explosive environment

. Do not use or store

the meter in high temperature, high humidity, flammable, explosive and strong magnetic

field environments.

Never open the casing of the product.

Only trained personnel can perform the

maintenance program. The instrument will not fully discharged after power off, which may

cause electric shock and injury.

Do not operate the product if you suspect it is faulty

. Please contact UNI-T authorized

service personnel for inspection. Please disconnect the power supply and stop using.

Never use the instrument beyond the dedicated range of instruction

. The provided

protection will be weaken or invalid. It is forbidden to use this product in life-support system

or other devices with safety requirements.

Only trained personnel can perform the maintenance program.

Any maintenance,

adjustment, or replacement of parts must be performed by UNI-T authorized maintenance

personnel.

Summary of Contents for UTL8500 Series






















































Search results

Summary of Contents for UTL8500 Series

Reviews:

Related manuals for UTL8500 Series

Brands by name

Popular brands

UNI-T UTL8500 Series, User Manual

Search results

Summary of Contents for UTL8500 Series

Reviews:

Related manuals for UTL8500 Series

Brands by name

Popular brands