background image

Quick Guide

UPO1000 Series

3/17

1.

Safety Requirements

This section contains information and warnings that must be followed to keep the instrument operating

under safety conditions. In addition, user should also follow the common safety procedures.

Safety Precautions

Warning

Please follow the following guidelines to avoid possible electric shock and risk to

personal safety.
Users must follow the following conventional safety precautions in operation,

service and maintenance of this device. UNI-T will not be liable for any personal

safety and property loss caused by the user’s failure to follow the following safety

precautions. This device is designed for professional users and responsible

organizations for measurement purposes.

Do not use this device in any way not specified by the manufacturer. This device is

only for indoor use unless otherwise specified in the product manual.

Safety Statement

Warning

“Warning” indicates the presence of a hazard. It reminds users to pay attention to a

certain operation process, operation method or similar. Personal injury or death

may occur if the rules in the “Warning” statement are not properly executed or

observed. Do not proceed to the next step until you fully understand and meet the

conditions stated in the “Warning” statement.

Caution

“Caution” indicates the presence of a hazard. It reminds users to pay attention to a

certain operation process, operation method or similar. Product damage or loss of

important data may occur if the rules in the “Caution” statement are not properly

executed or observed. Do not proceed to the next step until you fully understand and

meet the conditions stated in the “Caution” statement.

Note

“Note” indicates important information. It reminds users to pay attention to

procedures, methods and conditions, etc. The contents of the “Note” should be

highlighted if necessary.

Safety Sign

Danger

It indicates possible danger of electric shock, which may cause

personal injury or death.

Warning

It indicates that you should be careful to avoid personal injury or

product damage.

Caution

It indicates possible danger, which may cause damage to this device

or other equipment if you fail to follow a certain procedure or

condition. If the “Caution” sign is present, all conditions must be met

before you proceed to operation.

Note

It indicates potential problems, which may cause failure of this device

if you fail to follow a certain procedure or condition. If the “Note” sign

is present, all conditions must be met before this device will function

properly.

AC

Alternating current of device. Please check the region’s voltage range.

DC

Direct current device. Please check the region’s voltage range.

Summary of Contents for UPO1000 Series


















Reviews: