- 24 -
- 25 -
2
1
3
4
5
6
7
8
9
S
a
fe
ty
P
re
c
a
u
tio
n
s
B
e
fo
re
Y
o
u
B
e
g
in
T
ro
u
b
le
s
h
o
o
tin
g
S
p
e
c
ifi
c
a
tio
n
s
M
u
lt
i-
B
ra
n
d
IR
R
e
m
o
te
C
o
n
tr
o
lle
r
H
a
rd
w
a
re
D
e
s
c
ri
p
tio
n
s
C
o
n
n
e
c
tio
n
s
G
u
id
e
o
f
F
u
n
c
tio
n
s
6
G
u
id
e
o
f
M
a
in
M
e
n
u
Guide of Main Menu
e
LNB Power : Select the LNB power.
r
LNB Type : Select the LNB type.
t
LNB Frequency : Select the frequency that is set to antenna.
- Use the LEFT/RIGHT buttons to select the LNB frequency.
- If the required LNB frequency is not listed, then enter the frequency manually using
the NUMERIC buttons.
- When you select Universal in LNB type, both 9750 and 10600 are supported at the same time.
And LNB 22KHz setting is disabled.
y
LNB 22KHz: When you use a dual LNB or two antennas connected to a 22KHz tone switch box,
make 22KHz tone switch enable or disable to select LNB or antenna.
u
DiSEqC SW : If you use a DiSEqC 1.0 or DiSEqC 1.1 switch, select one of the DiSEqC inputs.
i
Positioner Setting : Press OK button to move to Positioner Setting menu directly.
o
Service Search : Press OK button to move to Service Search menu directly.
2.2 Positioner Setting
q
Satellite : Select the satellite what you want to search the service.
- Press the LEFT/RIGHT button to select the satellite.
- Select the wanted satellite name.
- If the desired satellite name is not listed then select User Defined.
w
Frequency : Select frequency what you want to check the signal.
e
Positioner : Select the positioner.
- Move : To move the dish, press LEFT/RIGHT button.
- Fine Move : To move the dish in detail, press LEFT/RIGHT button.
- Positioner Command : To use various positioner command, press
OK button. Then, available positioner commands will appear.
- Dish Setting : Press OK button to move to Dish Setting menu directly.
- Service Search : Press OK button to move to Service Search menu
directly.
Using DiSEqC 1.2
- Fine Move : To move the dish in detail, press LEFT/RIGHT button.
- Dish Longitude : Enter the longitude using the NUMERIC buttons.
- Dish Latitude : Enter the latitude using the NUMERIC buttons.
- Go To : Press OK button to rotate the dish to the configured position.
- Positioner Command : To use various positioner command, press
OK button. Then, available positioner commands will appear.
- Service Search : Press OK button to move to Service Search menu
directly.
Using USALS
- Dish Setting :
Press OK button to move to Dish Setting menu directly.
- Service Search :
Press OK button to move to Service Search menu directly.
None
2.3 Service Search
q
Satellite : Select the target satellite for search.
w
Search Mode : Select the following search mode.
- Search Type : Select the search type.
- Network Search : You can select
'Off'
or
'On'
. When you select
'On'
, you can find more transponders using the home network.
As it refers to NIT during searching, if there is the frequency
information of other transponder, it searches the other transponder
besides the transponder that the user inputs.
- Dish Setting : Press OK button to move to Dish Setting menu directly.
- Positioner Setting : Press OK button to move to Positioner Setting
menu directly
- Start Search : Press OK button to start search.
Auto Search Mode
- Frequency : Set
'Auto'
to search whole frequency, Set
'Manual'
to search only desired frequency.
- Polarity : Select the polarity.(
All Polarity
/
Vertical
/
Horizontal
)
- Search Type : Select the search type.
- Dish Setting : Press OK button to move to Dish Setting menu directly.
- Start Search : Press OK button to start search.
Blind Search Mode
- Frequency : Select the frequency from the list to search.
- Symbol rate : Enter the symbol rate using the NUMERIC buttons.
- Polarity : Select the polarity.(
Vertical
/
Horizontal
)
- Search Type : Select the search type.
- Network Search : You can select
'Off'
or
'On'
. When you select
'On'
, you can find more transponders using the home network.
As it refers to NIT during searching, if there is the frequency
information of other transponder, it searches the other transponder
besides the transponder that the user inputs.
- Dish Setting : Press OK button to move to Dish Setting menu directly.
- Start Search : Press OK button to start search.
Manual Search Mode
- Frequency : Select the frequency from the list to search.
- Symbol rate : Enter the symbol rate using the NUMERIC buttons.
- Polarity : Select the polarity.(
Vertical
/
Horizontal
)
- Video PID : Enter the video PID using the NUMERIC buttons.
- Audio PID : Enter the audio PID using the NUMERIC buttons.
- PCR PID : Enter the PCR PID using the NUMERIC buttons.
- Start Search : Press OK button to start search.
Advanced Search Mode
