background image

 

12

 

 

OPERATION: AUTOMATION 

TITAN DUAL LEG 

 

OPERATION: AUTOMATION 

Your product can be integrated into most control systems using dry contact relays. These instructions are 

provided for Automation specialist reference only. Please contact us, or an Automation specialist, before 

attempting this change.  

 
TO INTEGRATE:  

Unplug and remove the original controller and replace it with a DP1U Controller. This is needed as removing 

the original controller will remove any stored Up or Down limits. DP1U is used to set the Up and Down limits in 

the main control unit. 

 
SET NEW POSITIONS:

 

 

On the DP1U, press the UP arrow to bring to the desired height. Press the DOWN arrow to stop. Press the S 

button and within 2 seconds press the 1 button. Memory 1 is now set. 
Repeat procedure for other Memory positions. 
 

TO AUTOMATE: 

Plug in a standard CAT category LAN cable between the Control unit port A2 and external relays. Use the 

pinouts below to activate the desired action. Note: a single relay pulse will cause the lift to travel in the 

selected direction until it hits the full stroke length. A second pulse of the same relay will cancel the action. 
 

CONTROL BOX PINOUT: 

Function

 

Pins

 

Colour (T568A)

 

Colour (T568B)

 

Up

 

4 & 5 

Blue & Blue/White 

Blue & Blue/White 

Down

 

4 & 8 

Blue & Brown 

Blue & Brown 

Store

 

2 & 8 

Green & Brown 

Orange & Brown 

Memory 1

 

3 & 5 

Orange/White & 

Blue/White 

Green/White & Blue/White 

Memory 2

 

3 & 8 

Orange/White & Brown 

Green/White & Brown 

Memory 3

 

2 & 5 

Green & Blue/White 

Orange & Blue/White 

 
 

                                  

 

           DPU1 CONTROLLER 

 

    

 

      STANDARS CAT LAN CABLE 

Summary of Contents for TITAN TTN-000
















Reviews: