68
Section 19: Programming Guide — JJR XP8103
CONTINUED
“SW OFF” appears when the flap mixing is in
the middle of lower position
Elevator Operating Direction
(D=Down, U=Up)
Indicates the function selected
Elevator to Flap Mixing Value (Range ± 125%)
Indicates current mixing switch activated:
ON:
Always ON
MIX: Mixing Switch
FLP (-) D: ON when Flap Switchs in lower position
FLP (-) U: ON when Flap Switchs in upper position
Press the (+) or (-)
key to adjust the
UP and DN
mixing values or
to select the active
“mixing switch.”
Press either CH key
to select function:
↓
Rate
↓
SW
Press to return the mixing
value to zero or to return the
active mixing switch to ON.
DN
SELECT
CH
CH
CLEAR
UP
↓
Rate
↓
SW
Step 10. Mixing elevator to flap:
In Function mode, press
the
Up
key until “ELEV-FLAP Mix” appears on your screen. This
is the elevator-to-flap mix. Press the
CH
key move the cursor to
SW:. This allows you to select which switch will be used to turn
on/off the elevator-to-flap mixing. Pressing the (+) key will
select one of the following switches: MIX = mix switch (located
on the back right of the transmitter), FLP-D = flap switch down,
FLPU flap switch up, or ON = always on. We suggest selecting
the mix switch mix so the elevator-to-flap mix can be turned on
and off independently of the flaps. After selecting MIX, press the
CH
key to return the cursor to the rate position. With the mix
switch in the forward position, hold up elevator and press the
(+) key until a 35% value is achieved. Up should result in down
flaps. If the flap goes up, reverse the 35% value from a +35 to a
-35 using the (-) key. Now hold down elevator with the control
stick and press the (+) key until 35% is achieved. The flaps
should go up. Reverse the value if necessary until up elevator
gives down flaps and down elevator gives up flaps. Later you
can experiment with more or less flap throw by changing this
value. 35% is a good, safe place to start.
At rate, press to
increase/decrease mixing
value (± 125%).
At switch, press to change
switch Selection.
Press either CH key to
manipulate the arrow
from Rate to SW.
At rate, press to set mixing value to
factory preset (0%). At switch,
press to set switch to factory preset
(ON).
DN
SELECT
CH
CH
CLEAR
UP
Indicates the function
being selected:
“SW OFF” appears when the Flap Mixing is in the middle or
upper position
Aileron to Flap Mixing Value (Range ± 125%)
Indicates current mixing switch activated:
ON:
Always ON
MIX: Mixing Switch
FLP (-) D: ON when Flap Switchs in lower position
FLP (-) U: ON when Flap Switchs in upper position
Step 11. Aileron-to- mixing:
Press the
Up
key until the
“AILE-FLAP Mix” screen appears. Press the
CH
key to move the
cursor to the “SW:” position. The “SW:” allows you to select
which switch is used to turn on/off the aileron-to-flap mix.
Pressing the (+) key will select one of the following switches:
MIX = mix switch located on the back right of the transmitter,
FLP-D = flap switch down, F-U&D = flap switch up and down,
and ON = always on.
We recommended putting the aileron-to-flap mix on the mix
switch so the mix can be turned off independently from the flaps.
After selecting “MIX,” press the
CH
key to return the cursor to
the “Rate” position. Now press the (+) key until +100% value is
reached. Now the flaps should move in unison in the same
direction with the ailerons. If they move in opposite directions,
press the (-) key until a -100% value is reached.
↓
Rate
↓
SW
Summary of Contents for Hangar 9
Page 82: ...82 NOTES ...
Page 83: ...83 NOTES ...
Page 84: ... Copyright 2001 Horizon Hobby Inc 217 355 9511 www horizonhobby com HAN1675M 46 ...
