SYSTEM PROGRAMMING -
Menu 1
PAGE 16
80 SERIES
INSTALL MANUAL
TRANSMITTER PROGRAMMING
SYSTEM PROGRAMMING -
Menu 1
SYSTEM PROGRAMMING -
Menu 1
PAGE 17
80 SERIES
INSTALL MANUAL
DIAGNOSTICS
DIAGNOSTICS CHART
TO ENTER DIAGNOSTIC MEMORY
If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic
to indicate what shutdown input has been triggered. For example:
If the start
button is pressed the park
lights flash 3 times slowly.
Looking at the chart below this would indicate that the system is in Service Mode,
simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter
will begin to function as normal.
PARK LIGHTS STATUS LED
DIAGNOSTIC CODE
3 Slow Flashes LEDs “ON” Solid
System Is In Service Mode
4 Slow Flashes Series of 4 Flashes
Not in Reservation Mode
5 Flashes Series of 5 Flashes
Hood Open
5 Slow Flashes Series of 5 Flashes
Ignition On During Start Attempt
6 Flashes Series of 6 Flashes
Brake Pedal Shutdown
7 Flashes Series of 7 Flashes
Tach Lock-Out
8 Flashes
Series of 8 Flashes
3 Start Attempts Without Starting
Step 1-
Turn the ignition ON then OFF. Press and release the Program Button.
Step 2-
The system will respond with three park light flashes and the HORN (optional) will honk the same
number of times as the events in memory.
****
Maximum four events, four honks****
NOTE:
If the HORN does not honk, there are no events in memory.
Step 3-
Press the Program Button once to view the last shut down code. The HORN (optional)will honk
once to confirm code one.
****
If the HORN does not honk, there are no codes in memory.****
Step 4-
The LEDs on the antenna will flash a code corresponding to a shut down trigger. Press the
Program Button again for the second code.
***
The HORN will honk twice to confirm code two three time for code three...***
Step 5-
To
Clear Diagnostic Memory.
While in Diagnostic Mode press and hold the
Program Button for five seconds. The park lights will flash and the HORN (optional)
will honk once.
****
Once diagnostic memory has 4 shutdown events in memory, the system will not record any further
shutdown events until the system memory has been cleared.****
LED Flashes Diagnostic
5 Flashes The system was shutdown by the brake switch input
6 Flashes The system was shutdown by the hood pin input
7 Flashes The system did not detect the Tach signal.
8 Flashes The system made 3 start attempts without starting
ENTERING REMOTE PROGRAM MODE
The system can lean up to 4 different remote’s. Each remote to be used MUST
be programmed together during the same sequence. For security, when a new
remote is programmed all previous remote’s are deleted. Please see remote
operation chart for information on using Second Car / Pad Lock Operations.
HOLD the program switch, the HORN will honk ONCE and the park lights will
turn on. (If the HORN does not honk repeat step 1) CONTINUE TO HOLD until
the HORN honks 5 times
Press & Release LOCK (START ON 1172) button on 1st Remote to be
Programmed for Normal Operation
If remote(s) are to be
programmed for "PADLOCK" skip and goto step 6.
Press & Release BUTTON 4 on Remote to be Programmed
for 2ND CAR OR PAD LOCK
HORN will honk 1 time to confirm remote has been
programmed (If the HORN does not honk press button again)
HORN will honk 1 time to confirm remote has been
programmed (If the HORN does not honk press button again)
PROGRAMMING REMOTE’S
Cycle the Ignition Key - ON/OFF ON/OFF ON
(Leaving the key ON)
Turn ignition key OFF to exit remote program mode when
all required remote’s have been programmed.
1 honk confirms program mode entered followed by
5 honks confirming transmitter program mode
1 -
2 -
3 -
4 -
6 -
5 -
7 -
8 -
REPEAT STEP 4 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR NORMAL OPERATION
REPEAT STEP 6 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR 2ND CAR / PADLOCK OPERATION
To program 2nd car operation on 2way models enter transmitter program mode and turn the # icon
on then program the transmitter to the vehicle. If the # icon is on the remote is in 2nd car operation
.
