13 PIN CONNECTOR
SYSTEM PROGRAMMING -
Menu 1
PAGE 12
80 SERIES
INSTALL MANUAL
SYSTEM WIRING DETAILS
PARK BRAKE INPUT. M SERIES REMOTE STARTER ONLY.
YELLOW
BROWN
GRAY
RED/WHT
ORG/WHT
WHT/VIO
PINK
GRN/WHT
BLUE/WHT
BLUE
PURPLE
GREEN
OUTPUT FOR FACTORY ALARM RE-ARM
OUTPUT FOR FACTORY ALARM DIS-ARM
NEGATIVE STARTER OUTPUT
OUTPUT FOR TRUNK RELEASE ACTIVATION
NEGATIVE ACCESSORY OUTPUT/ AUXILIARY OUTPUT 2
AUXILIARY OUTPUT 1/ PROGRAMMABLE OUTPUT
BRAKE SWITCH INPUT (+) WHEN BRAKE IS PRESSED
HOOD PIN SWITCH INPUT
TACH WIRE INPUT
WAIT TO START (DIESEL VEHICLES)
POSITIVE DOOR PIN INPUT (ALARMS AND MANUAL* ONLY)
NEGATIVE DOOR PIN INPUT (ALARMS AND MANUAL* ONLY)
BLK/WHT
*MANUAL TRANSMISSION MODEL REQUIRED
SEE OWNERS MANUAL FOR RESERVATION
MODE PROCEDURE.
1-YELLOW Re-arm(-)
(Programmable) - Supplies one .75 second pulse when
locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ RAP
shutdown.
2-BROWN Dis-arm(-)
- .75 second pulse when unlock button is pressed and one
.75 second pulse before remote start activation. For factory alarm dis-arm/ “wake up”.
3-GRAY
(-) Start/ Crank -
Negative output during crank/ start.
4-RED/WHITE Trunk Release(-)
(Programmable)- Output will activate when the
Unlock button is held for at least 3 seconds. The output will stay on for 5 seconds or until
the button is released
5- ORG/WHT 2nd Acc (-) / Auxiliary Output 2
(Programmable) - Ground output at
the same time as the primary Accessory. output. This output can be programmed to
activate as and auxiliary output when the unlock and start buttons are held.
6- WHT/VIOLET Auxiliary Output 1/ Programmable Output
- Auxiliary output when
the # button is held. Programmable to (-) Ignition/ Car Finder and Dome Light Supervision
with Car Finder.
(Car Finder and Auxiliary 1 are not available on 2way models)
7- PINK Brake Switch input (+) -
This wire must be connected to the wire at the
brake switch that changes to 12volts when the brake is pressed.
Manual Transmission Only. -
Alarm & Manual Transmission Only. -
*Connect to door pin for Passive Arming on non alarm models.
8- BLACK/WHT Park Brake Input (-)
Connect to the
Park Brake wire. Must be connected on manual transmission models.
9- GREEN/WHT Hood Pin Input (-) -
Connect
this wire to the supplied hood pin switch.
If ground is detected on this input the remote starter will not activate.
10- BLUE/WHT Tach Wire Input (A/C) -
This wire is
used to
to detect when the vehicle
has started. The Tach source is typically taken from a fuel injector, coil, coil pack or crank
position sensor. The Tach wire is generally found as the opposite from the common wire
at the coil or fuel injector.
11- BLUE Wait to Start Input (+ or -)
(Programmable) - On diesel vehicles
connect this wire to the wait to start or glow plug wire. The system will wait for the input to
turn off then remote start. A start delay may also be programmed to avoid this connection.
12- PURPLE Positive Door Input (+) Alarm & Manual Transmission Only. -
Connect this wire to the door pin switch if it changes to 12volts when the door is opened.
*Connect to door pin for Passive Arming on non alarm models.
13- GREEN Negative Door Input (+)
Connect this wire to the door pin switch if it changes to Negative when the door is
opened.
SYSTEM PROGRAMMING -
Menu 1
PAGE 13
80 SERIES
INSTALL MANUAL
SYSTEM WIRING DETAILS
