Ultra Start 35 SERIES Install Manual Download | Manualshive

Page: 1 / 24

background image

INSTALL GUIDE

www.ultrastarters.com

Technical Support: 866-698-5872 ext 0

[email protected]

Covers All 35xx Series Advanced

2-Way Remote Starters

The system must be placed into Service Mode before any service work is started on the
vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The
manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always be Installed!

Warning!!

CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!

It is the sole responsibility of the user to place the system in Service Mode
when parking in an enclosed area

ex: garage

, partially enclosed area

ex: carport,

or when the vehicle is being serviced.

1
2
3
...
»

Summary of Contents for 35 SERIES

























Reviews:

No comments

Related manuals for 35 SERIES

Brand: Fantini Cosmi Pages: 25

ServLink ACR3500A

Brand: Black Box Pages: 115

Brand: Voxx Electronics Pages: 11

Brand: La Crosse Technology Pages: 13

Brand: Zenith Pages: 6

Brand: Midea Pages: 15

Brand: Daspi Pages: 15

AT8560 AllTouch

Brand: Scientific Atlanta Pages: 28

Brand: Robokits Pages: 5

Brand: Mitsubishi Pages: 51

Brand: Mitsubishi Pages: 16

Brand: Mitsubishi Pages: 46

Brand: Mitsubishi Pages: 206

Brand: HeathZenith Pages: 16

Brand: Genius Pages: 4

Brand: Bolton Conductive Systems Pages: 3

Brand: Task Force Tips Pages: 2

Brand: Dometic Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands