Ultra Start 35 SERIES Install Manual Download Page 10

Page: 10 / 24

Step 1 - Connect All Of the Following Wires

Main Connector (6pin)

YELLOW

Starter Output

- 12volts during start position only.

GREEN

Heater/Acc Output

- 12volts in the accessory position off during

start and 14volts during run.

RED

12volt 30amp Input

- 12volts from ignition harness or battery.

RED

12volt 30amp Input

- 12volts from ignition harness or battery.

BLUE

Ignition Output

- 12volts in the ignition, start and run positions.

WHITE*

Selectable Output

- Selectable Output for vehicles that may

require a 2nd Ignition, Accessory or Start.

*(

See jumper diagram page 7)

Auxiliary Connector (14pin)

BLACK

System Ground Input

- Connect to Chassis Ground.

WHITE

Park Light Output

- Connect to Park Light system.

GRN/WHT

Hood Pin Input

- Connect to the Hood Pin Safety Switch.

BLUE/WHT*

Tach Input

- Connect to A/C Tach source. (Above 2 volts AC)

PINK

Brake Switch Input

- Connect to 12volts when the brake pedal

is applied.

Not necessary on TL models only.

“M” Series

(yellow case)

BLK/WHT

Park Brake Input

- Connect to Park Brake wire.

GREEN** or

Door pin Input

- Connect to (-) wire when door open

PURPLE**

Door pin Input

- Connect to (+) wire when door open

Connect only ONE of the door input wires.

Important!

Never install an AUTOMATIC TRANSMISSION module into a
MANUAL TRANSMISSION vehicle!

INSTALL MANUAL

REMOTE VEHICLE STARTER

PAGE 10

Summary of Contents for 35 SERIES

























Search results

Summary of Contents for 35 SERIES

Reviews:

Related manuals for 35 SERIES

Brands by name

Popular brands

Ultra Start 35 SERIES, Install Manual

Search results

Summary of Contents for 35 SERIES

Reviews:

Related manuals for 35 SERIES

Brands by name

Popular brands