manualshive.com logo in svg

Ultra Start 35 SERIES, Install Manual

Share
Download
Ultra Start 35 SERIES Install Manual Download Page 19

Setting 5  Maximum Crank Time

1)  10 Seconds      1 Flash/Honk           10 sec max time that the starter will stay engaged.
2)    3 Seconds      2 Flashes/Honks      3 sec max time that the starter will stay engaged.

*3)   5 Seconds    3 Flashes/Honks      5 sec max time that the starter will stay engaged.

Press & Release the Program Button 

5 Times (Setting 5) Confirmed with 5 LED flashes.

Press & Hold the Program Button 

until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

 to proceed to the next step.

Setting 6  Anti-Grind/Starter Kill

  (Auxiliary Connector Pin 4)

1)  Active      1 Flash/Honk       (-)When locked and during remote start (Anti-Grind).
2)  Passive  2 Flashes/Honks  (-)When locked/ 30 seconds after ignition is OFF or 

 

 pressed

*3)  GWR     3 Flashes/Honks  (-) Output during remote start only. (Anti-grind/ Bypass)

Press & Release the Program Button 

6 Times (Setting 6) Confirmed with 6 LED flashes.

Press & Hold the Program Button

 until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

 to proceed to the next step.

REMOTE VEHICLE STARTER                                                         

INSTALL  MANUAL

                                                                                                                                PAGE 19

Menu 3- Starter Settings

 - continued

Summary of Contents for 35 SERIES

























Reviews:

No comments

Brands by name

Popular brands

Load more brands