Ultra Start 35 SERIES Install Manual Download

Page: 17 / 24

Setting 1 Secure Valet Mode

(time required to set the system into Service Mode)

1) Secure Valet 1 Flash/Honk Hold the Program Button for 15 seconds

*2) Normal Valet 2 Flashes/Honks Hold the Program Button for 5 seconds

Press & Release the Program Button 1 Time

(Setting 1) confirmed 1 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 2 Parking Light/Trunk Output

(14 pin auxiliary connector pins 2&8)

1) 30 sec. Output 1 Flash/Honk On for 30 seconds when

is pressed

2) Negative Park Lights 2 Flashes/Honks Switches the Park Lights/Trunk Outputs

*3) Park Lights 3 Flashes/Honks 2 Flashes when

is pressed

Press & Release the Program Button 2 Times

(Setting 2) confirmed 2 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 3 Horn Honk Timing

(14 pin auxiliary connector pin 5)

1) 5 ms Pulse Output 1 Flash/Honk Short(Quiet) Horn Output Pulses
2) 15 ms Pulse Output 2 Flashes/Honks Long(Loud) Horn Output Pulses

*3) 10 ms Pulse Output 3 Flashes/Honks Normal(Medium) Horn Output Pulses

Press & Release the Program Button 3 Times

(Setting 3) confirmed 3 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 4

Button Operations

*3) Car Finder 3 Flashes/Honks Button activates Car Finder Mode

Press & Release the Program Button 4 Time

(Setting 4) confirmed 4 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 5 Reservation Mode ( “M” units only)

1) Manual Reservation 1 Flash/Honk Activate Reservation Mode by pressing Button

*2) Auto Reservation 2 Flashes/Honks Activate Reservation Mode by pressing brake

Press & Release the Program Button 5 Time

(Setting 5) confirmed 5 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

REMOTE VEHICLE STARTER

INSTALL MANUAL

PAGE 17

Menu 2- Additional Settings

Press and

Release the

button for
Menu 2

Ignition 3x

On/Off

On/Off On

Press and

Release the

Program

Button

Press and Release

the Program Button

# of Times for

Setting Chosen

Press and Hold

the Program Button

to Change Option

Summary of Contents for 35 SERIES

























Search results

Summary of Contents for 35 SERIES

Reviews:

Related manuals for 35 SERIES

Brands by name

Popular brands

Ultra Start 35 SERIES, Install Manual

Search results

Summary of Contents for 35 SERIES

Reviews:

Related manuals for 35 SERIES

Brands by name

Popular brands