Installation Guide
Press the Program Switch 7 times
to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and siren chirps..
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Setting 7- Sensor Disconnect
10
1 Positive Input To Start
1 Flash
Positive pulse will activate remote starter.
2 Positive Disconnect
2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
PROGRAM MODE - STARTER SETTINGS
Enter Starter Program Mode - See Page 7 for details on entering program mode
1
Chrysler / VW Re-Arm
1 Flash
Unlock pulse before start and a lock pulse after start
2
GM Auto Re-Lock
2 Flashes
Lock pulse after remote starter shuts off
3*
Normal Operation
3 Flashes
No additional re-lock pulses
1
Diesel Glow Plug
1 Flash
W
2
Timed Delay
2 Flashes
Ignition ON for 10 seconds before engaging remote starter
3*
Gas Mode operation
3 Flashes
Waits 2 seconds before engaging starter output
aits a Maximum of 3:20 second before starting.
1
Type 1
1 Flash
Pulse after start and with lock
2
Type 2
2 Flashes
Pulse after start only
3*
Factory Re-arm 3 Flashes
0.75 second pulse with lock and after shutdown
Setting 1- Special Door Lock/ Unlock Operations
Setting 2- Gas/ Diesel Mode-
Blue Wire on 14-Pin
Setting 3- Rearm Output-
Yellow Wire on 14-Pin
1
30 Min Run Time
1 Flash
Remote Starter runs for 30min when activated
2
45 Min Run Time
2 Flashes
Remote Starter runs for 45min when activated
3*
15 Min Run Time
3 Flashes
Remote Starter runs for 15 min when activated
1
10 Seconds
1 Flash
10 sec Max time that starter will stay engaged
2
3 Seconds
2 Flashes
3 sec Max time that starter will stay engaged
3*
5 seconds
3 Flashes
5 sec Max time that starter will stay engaged
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Sensor Disconnect
1 Positive Input To Start
1 Flash
Positive pulse will activate remote starter.
2 Positive Disconnect
2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
Continued on next page...
Press the Program Button 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 4 times
to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times
to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 6 times
to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button.
Press momentarily to move to next program step or repeat to change selection.
