1 Type 1
1 Flash
Pulse after start and with lock
2 Type 2
2 Flashes
Pulse after start only
3* Factory Re-arm 3 Flashes
0.75 second pulse with lock and after shutdown
Press the Program Button 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 30 Min Run Time 1 Flash
Remote Starter runs for 30min when activated
2 45 Min Run Time 2 Flashes
Remote Starter runs for 45min when activated
3* 15 Min Run Time 3 Flashes
Remote Starter runs for 15 min when activated
1 10 Seconds
1 Flash
10 sec Max time that starter will stay engaged
2 3 Seconds
2 Flashes
3 sec Max time that starter will stay engaged
3*5 seconds
3 Flashes
5 sec Max time that starter will stay engaged
1Active Starter Kill 1 Flash
On when locked, Before ignition and 2 seconds after ignition turns off.
2Passive Starter Kill 2 Flashes
Same as setting 1 but will arm 60sec after the ignition turns off.
3*Bypass Module 3 Flashes
Output before ignition. Stays on 2 seconds after ignition turns off.
1 Safety ON
1 Flash
Must press the start button twice to remote start the vehicle
2* Safety OFF
2 Flashes
Press the start button once to remote start the vehicle.
Press the Program Button 4 times
to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times
to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 7 times
to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 6 times
to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Starter Kill/ Bypass Module Output- Orange wire on 14-Pin Con.
Setting 7- Safety Start Mode
PROGRAM MODE 3 - STARTER SETTINGS
1 Type 1
1 Flash
Unlock before start. Lock pulse after start and shutdown
2 Type 2
2 Flashes
Lock pulse only after remote starter shuts off
3* Normal Operation 3 Flashes
No additional re-lock pulses
Setting 1- Special Door Lock/ Unlock Operations
Press the Program Button 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and horn honks.
Press the Program Button 2 time
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
1 Negative Input/ 30seconds
1 Flash
Waits a maximum 30 seconds before starting.
2 Timed Delay/ 15 Seconds
2 Flashes
Ignition ON for 15 seconds before engaging remote starter
3* Gas/ Positive Glow Plug
3 Flashes
Waits 2 seconds to start if no diesel input is detected
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
Page 9
Installation Guide
