background image

Step 1

 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON  -

Leaving Key ON

Step 2

 - Press and hold the Program Switch - Parking Lights will come ON **if park-lights do not come on

at this point, turn key off for 5 seconds, the repeat step 1.

Step 3

 - Continue to hold the Program Switch until the horn honks 5 times and the park lights go out.

Step 4

 - Continue to hold the program switch and press the 

LOCK

 button on each of 

1st car 

remote’s

and press the 

#

 button on each of the 

2nd car

 remote’s of the transmitters to be programmed. The park 

Lights will flash once and the horn will honk once each time a new code is learned. 

Note:

Transmitter programming must done within 5 seconds.

All  the transmitters

 to be used  must be 

programmed at the same time.

Any transmitters not reprogrammed at this time will be erased from 

memory for security.
**The system holds a maximum of 4 transmitter codes including 2nd car remote codes.

You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a 
second vehicle.

ACTIVATING Service Mode

1.

While the ignition is “ON”   press and hold the Program   Button for five seconds. The

park lights will flash five times and the horn (optional)will honk   five   times to confirm 
that the system is in Service Mode. 

2.

 While in Service Mode the remote start functions will be disabled and LED’s will be 

“ON” steady.  Door locks and trunk release are still operational.

DEACTIVATING Service Mode

1. While the ignition is “ON”   press and hold the Program   Button for five seconds. The park

lights will flash two times and the horn (optional)will honk   two   times to confirm that the 
system has exited   Service Mode. 

2. Remote start functions will return to normal operation.

+

-

Carefully remove the 

screw from back of 

the remote. 

Remove top case

then replace the 

battery.

Replace top case.

Re-install screw.

Test remote for 

proper operation.

The transmitter battery should be changed at least once every year to maintain proper operating range.
Replace with quality23A 12volt Alkaline battery.

Transmitter Programming

System Service Mode

System Service Mode - By Remote

Battery Replacement 

To ACTIVATE Service Mode

 - Press and Release button #4 then press and Button #4 again for 6 seconds until 
Status LED’s come on Solid.

Note: If horn is connected the horn will chirp 5 times.

To DEACTIVATE Service Mode

- Press and Release button #4 then press and Button #4 again for 6 seconds until 
Status LED’s turn off.

Note: If horn is connected the horn will chirp 2 times.

Page 11

Installation Guide

Summary of Contents for 1250 SERIES













Reviews: