background image

6 Pin Power Connector

6-pinDescription

Test For Wire

1-Yellow

30amp Starter Output

-

This wire will test 0volts in off, accessory and in

the ignition position.12volts during start only.

2-Green

30amp Heat/Acc Output

-

This wire will test 0volts in the off position 12-

14volts in the accessory and run positions and 0 volts during start

3-Red

30amp Power Input

-

12volts at ignition harness or from battery.

Supplies power for the ignition, selectable output and park light relays.

4-Red

30amp Power Input

-

12volt power at ignition harness or from battery.

Supplies power for accessory and start relays

5-Blue

30amp Ignition Output -

This wire will test 0volts in the off and accessory

position 12volts in the ignition, start and run

.

6-White

30amp Select Output -

Selectable output for 2nd Ign, acc or starter.

Auxiliary Connectors - 4, 11 and 14 pin Connectors

Pin Number Function Description
1-Yellow

Re-Arm Output

-

0.75 second pulsed output when locked and on remote

start shutdown. Used for factory alarm re-arm

.

Programmable output. See Menu 3

2-Red/Wht Trunk Release Output (-) -

Hold the unlock button for 3 seconds.

Output will stay on until the unlock button is released (Max 5 seconds)

Programmable to (-)Park lights. See Menu 2

3-Brown

Disarm Output (-)

-

0.75sec pulsed output when unlocked and pulse before

remote start activation. Used for Factory Alarm Disarm.

4-Orange

Starter Kill and Negative While Run Outpu

t (-) -

Active when locked

and/or during remote start.

Anti-Grind -

Used for optional starter disable, and anti-grind relay

.

Programmable output. See Menu 3

5-White/ Blue Horn Output (-)

-

Output to activate factory horn.

Programmable output See Menu 1&2

6-Black/White Park Brake Input (-) -

Input to detect Park Brake Switch.

Connect switch that provides (-) when the switch is applied.

7-Purple

Door Pin Input (+)

-

Input to detect door opening.

Connect to door pin that switches to 12volts when the door opened.

8-White

Park Lights Output (+) -

+10amp park light output. Connect At light harness

0volts when Parking Lights are off, 12volts when park lights are on.

9-Green/White - Hood Pin Input (-) -

Negative input from hood pin safety switch.

Switch is grounded when the hood is opened. Must be connected.

10-Green Door Pin Input (-) -

Input to detect door opening.

Connect to door pin that switches to Negative when the door is opened.

Page 8

INSTALLATION MANUAL

REMOTE VEHICLE STARTER

Summary of Contents for 12 SERIES

























Reviews: