background image

Quick View Programming

* See the following pages for more detailed programming instructions.
Menu 1 - Press Lock

1 Flash

2 Flashes

3 Flashes

1 Ignition Lock

Enabled

Lock Only

Disabled

2 Horn Honk

Type 1

Type 2

All Honks

3 Lock&Unlock Options

Double Unlock

3 second

.75 second

4 Unlock/Disarm

125ms

750ms

Menu 2 -Press Unlock

1 Flash

2 Flashes

3 Flashes

1 Secure Service Mode

15 seconds

5 seconds

2 Park Light Output

30 seconds

(-) Park Light

Park Light Flash

3 Horn Timing

5ms

50ms

10ms

4 Button #4 (# Button)

Trunk Release

Garage Door

Car Finder

5 Reservation Mode

Manual

Auto Reservation

Menu 3 -Press Start

1 Flash

2 Flashes

3 Flashes

1 Lock/ Unlock Type

Type 1

Type 2

Normal

2 Gas/ Diesel

Negative

15 second

Gas/ Positive

3 Rearm Output

Type 1

Type 2

Rearm

4 Run Time

4 Min

45 Min

15 Min

5 Crank Time

10 seconds

3 seconds

5 seconds

6 Starter Disable/GWR

Active

Passive

GWR

7 Safety Start Mode

Press twice

Press once

Menu 4 -Press #

1 Flash

2 Flashes

3 Flashes

1 Low Idle Learn

Low Idle Learn

2 Adjust For Over Crank

Reduced by 10%

3 Adjust For under Crank

Increased by 10%

**Bold type indicates settings that are Factory Default.

System Reset

The system reset will clear any changes made to the Program Menu’s as well as the
Tach setting. When the system reset is complete the system must be Tach learned
before the remote starter will operate.

1)

Turn the ignition key from “Off” to “On” 3 times,

ON-OFF-ON-OFF-ON

within three

seconds

.

(Leave the key in the

ON

position)

2)

Press and release the

Program Button

located on the antenna. The park lights will

turn on and the horn (optional) will honk one time.

3)

Then press and hold the

Program Button

until the park lights flash and the horn

(optional) will honk 3 times slowly to confirm system reset.

System is now reset to factory defaults

.

Note:

System Reset

does not

delete the transmitter codes from memory.

Page 15

REMOTE VEHICLE STARTER

INSTALLATION MANUAL

Summary of Contents for 12 SERIES

























Reviews: