background image

Wiring Diagram auxiliary connectors

Door lock output

Door unlock output

(-) When Running

Low Current (-) Output
Low Current (+) Output

Door lock module output only*

ACTIVE RF ANTENNA**

(-) 500ma Output

(-) 250ma Output

(-) 250ma Output

(-) 500ma Output

(+) 500ma Output

1 2

3

The jumpers control the output from the

WHITE

wire on the 6- pin harness. This is an

30amp relayed output

. Place the jumpers in the following order to change the output.

If the jumper is in position #1 the output on the white wire will be

2nd Starter

If the jumper is in position #2 the output on the white wire will be

2nd Accessory

If the jumper is in position #3 the output on the white wire will be

2nd Ignition

*The factory default setting of the selectable output jumper is position #3.

Output on White wire

Jumper position

Second Starter

Position 1

Second Accessory

Position 2

Second Ignition

Position 3

Status Led’s

Program Button

**The antenna MUST be connected for the system to operate

*

The centre pin of the keyless entry harness is not to be used for anything besides

plug-in devices such as the VP-1, DL-3, DL-7 and Data Bus Modules. Overloading
this output will damage the remote starter.

1

2

3

1

2

3

4

1

2

3

1

2

*Temperature Sensor (LT Models Only)

*Input Trigger To Start 1350 Series

*Not available on 1250 Series

Green

White/Violet

Blue

Black

Red

Red

Jumpers

Page 7

REMOTE VEHICLE STARTER

INSTALLATION MANUAL

Summary of Contents for 12 SERIES

























Reviews: