background image

2

UAS P-Series Service Manual 574-848-2200

Notes, Cautions, and Warnings

Reading through the procedures, you will see NOTES, CAUTIONS, and 

WARNINGS. Each is there for a specific purpose.

NOTES 

give additional information that will help you complete the procedure.

CAUTIONS 

warn against making an error that could damage the vehicle.

WARNINGS 

remind you to be careful when there is risk of personal injury.

Below are some basic WARNINGS that you should heed when you work on the vehicle’s body. They are 

not all-inclusive and common sense must be used when servicing vehicles.

•  Always read and understand all instructions before starting a repair.
•  Always wear safety glasses and other appropriate protective equipment (gloves, steel-toed shoes, 

face shields, knee pads, hearing protection).

•  Put the transmission in Park and set the parking brake before working on the vehicle.
•  Be sure that the ignition switch is Off unless otherwise required by the procedure.
•  Only operate engines in a well-ventilated area.
•  Read and understand all warning labels.
•  Always remove rings, watches, hanging jewelry, and loose clothing before working in tight 

areas.

•  Always make sure tools are in proper working condition and have guards and safety devices in 

place.

• 

Use only the recommended tools for a specific job.

• 

If at any time you lack confidence in performing a specific repair procedure or in operating the 

tools safely to perform the repair, STOP! Call your local dealer or a Utilimaster representative.

When you see this symbol, read this statement first! This alert highlights information that may 

reduce the risk of personal injury or vehicle damage.

Summary of Contents for P-Series




















Reviews: