background image

User Manual  |  

27

EN

F- THINGS THAT MUST BE DONE BEFORE CALLING AUTHORIZED 

SERVICE

Troubleshooting 

The failures and solutions stated in this section can be performed easily by yourselves and always consult 

to an Authorized Service if these suggestions do NOTE solve your problem. 

Troubleshooting

Possible Solution

Result

Device is NOTE working. (No sound 

or only fan sound comes from the 

product.)

It may be due to the thermostat

NOTE plugged in. The fuse may be 

blown or broken down.

Condenser lamella may be 

obstructed or get dirty.

It will run again when 

reached to the suitable 

temperature. 

Insert the plug properly. 

Consult to an Authorized 

Service or a competent 

electrician.

Clean the condenser lamellas.

Device internal temperature is high.

External ambient temperature is 

very high or wrong thermostat 

setting.

Very close to the back wall, 

ventilation shutters are obstructed 

or it’s front is prevented.

It may have been expose to 

excessive external wind. 

Condenser lamellas are very dirty.

Move the device to a 

place where the external 

temperature is lower. 

Adjust to the stated gap.

Clean in front of the 

ventilation shutters. 

Prevent the wind. 

Clean the condenser lamellas.

Device internal temperature is very 

low.

Wrong internal thermostat setting.

Re-set the thermostat.

High degree of sweating on the 

glass and inside the device.

Water discharge hole may be 

obstructed when sweating is seen 

inside the cabin.

In glass sweating on the other hand, 

current external ambient humidity 

is over 65%.

Clean water discharge hole. 

With regards to the high 

humidity, you can move your 

device to an environment 

with less humidity.

Bad smell coming from the bottom 

part of the device.

Lower water discharge tray is dirty.

Clean the water discharge 

tray.

CAUTION!

 

•  Intervention to any failure that may occur in your product must be carried out by Authorized Ser-

vice.

•  Any intervention that may be done by you may harm you, your employee or customer, invalidate 

the product guarantee and cause material damage (fire etc..).

•  In case of any failure, consult to Customer Care or Authorized Service.
•  Consult your salesperson to order spare parts and for minimum period during which spare parts, 

are available. 

•  Please contact the sellerfor the minimum duration of the guarantee.

Setting the digital thermostat values other than the factory settings are completely under 

the user's responsibility. Our company shall NOTE be held responsible for the material and 

moral losses that may arise in connection thereto.

Summary of Contents for UDD 45 DTK





























Reviews: