Uflex Velair i10 VSD SMART Installation And User Manual Download Page 6

6

GEnERAL InFORMATIOn

 GENERAL  INFORMATION

1�1    About the manual

This manual was written to provide all the explanations for 

the correct management of the appliance.

 

This instruction manual forms an integral part of the 

device and therefore must be carefully preserved and 

must ALWAYS travel with it, even if you transfer the de-

vice to another owner or relocate it to other premises. 

If the manual gets damaged or lost, download a copy 

from the website.

 

Read this manual carefully before proceeding with any 

operation and follow the instructions in the individual 

chapters.

 

The manufacturer is not responsible for damages to 

persons or property caused by failure to follow the in-

structions in this manual.

 

This document is restricted in use to the terms of the 

law and may not be copied or transferred to third par-

ties without the express authorization of the manufac-

turer.

1�1�1    Editorial  pictograms

The pictograms in the next chapter provide the necessary 

information for correct, safe use of the machine in a rapid, 

unmistakable way.

 Related to security

 

High risk warning (bold text)

•  The operation described above presents a risk of se-

rious physical injury, fatality, major damage to the ap

-

pliance and/or to the environment if not carried out 

in compliance with safety regulations.

 

Low risk warning (plain text)

•  The operation described above presents a risk of mi-

nor physical injury or minor damage to the appliance 

and/or to the environment if not carried out in com-

pliance with safety regulations.

 

Prohibition  (plain text)

•  Refers to prohibited actions.

 

Important information (bold text)

•  This indicates important information that must be 

taken into account during the operations.

 In the texts

Purpose of the actions:

– Actions required

Expected responses following an action

•  Lists

Inthefigures

1  The numbers indicate the individual components.

A  The capital letters indicate component assemblies.

1

 

 The white numbers in black marks indicate a se-

ries of actions to be carried out in sequence.

A

 

 The black letter in white identifies an image when 

there are several images in the same figure.

1�1�2    Pictograms on the product

Symbols are used in some parts of the appliance:

 Related to security

 

Caution: electrical danger

•  The concerned personnel is informed to the pres-

ence of electricity and the risk of suffering an electric 

shock.

1�1�3    Recipients

User

non-expert person capable of operating the product in 

safe conditions for people, for the product itself and the 

environment, interpreting an elementary diagnostic of 

faults and abnormal operating conditions, carrying out 

simple adjustment, checking and maintenance operations.

Installer

Expert person qualified to position and connect (hydrau

-

lically, electrically, etc.) the unit to the plant; this person is 

responsible for handling and correct installation according 

to the instructions provided in this manual and the national 

standards currently in force.

To work on the refrigeration circuit, the installer must com-

ply with the provisions of Regulation 303/2008/EC which 

defines, in accordance with Directive 842/2006/EC, the re

-

quirements for companies and personnel with regard to 

fixed refrigeration, air conditioning and heat pump equip

-

ment  containing  certain  fluorinated  greenhouse  gases 

(F-gas licence).

Technical Service Centre

Expert  and  qualified  person  authorised  directly  by  the 

manufacturer to carry out all routine and supplementa-

ry  maintenance  operations,  as  well  as  every  adjustment, 

check, repair and replacement of parts necessary during 

the life of the unit itself.

Service personnel must comply with the provisions of Reg-

ulation 303/2008/EC which defines, in accordance with Di

-

rective 842/2006/EC, the requirements for companies and 

personnel with regard to fixed refrigeration, air condition

-

ing and heat pump equipment containing certain fluorinat

-

ed greenhouse gases (F-gas licence).

1�1�4    Manual  organisation

The manual is divided into sections each dedicated to one 

or more target groups.

General information

It addresses all recipients.

Summary of Contents for Velair i10 VSD SMART

































Reviews: