IMTX200H-03
www.ueonline.com
CP04112000
U N I T E D E L E C T R I C
C O N T R O L S
180 Dexter Avenue, P.O. Box 9143
Watertown, MA 02471-9143 USA
Telephone: 617 926-1000 Fax: 617 926-2568
http://www.ueonline.com
RECOMMENDED PRACTICES AND WARNINGS
United Electric Controls Company recommends careful consideration of the fol-
lowing factors when specifying and installing UE pressure and temperature units.
Before installing a unit, the Installation and Maintenance instructions provided
with unit must be read and understood.
• To avoid damaging unit, proof pressure and maximum temperature limits stated
in literature and on nameplates must never be exceeded, even by surges in the
system. Operation of the unit up to maximum pressure or temperature is accept-
able on a limited basis (e.g., start-up, testing) but continuous operation must be
restricted to the designated adjustable range. Excessive cycling at maximum
pressure or temperature limits could reduce sensor life.
• A back-up unit is necessary for applications where damage to a primary unit
could endanger life, limb or property. A high or low limit switch is necessary
for applications where a dangerous runaway condition could result.
• The adjustable range must be selected so that incorrect, inadvertent or mali-
cious setting at any range point cannot result in an unsafe system condition.
• Install unit where shock, vibration and ambient temperature fluctuations will
not damage unit or affect operation. When applicable, orient unit so that
moisture does not enter the enclosure via the electrical connection. When
appropriate, this entry point should be sealed to prevent moisture entry.
• Unit must not be altered or modified after shipment. Consult UE if modifica-
tion is necessary.
• Monitor operation to observe warning signs of possible damage to unit, such
as drift in set point or faulty display. Check unit immediately.
• Preventative maintenance and periodic testing is necessary for critical appli-
cations where damage could endanger property or personnel.
• Electrical ratings stated in literature and on nameplate must not be exceed-
ed. Overload on a switch can cause damage, even on the first cycle. Wire
unit according to local and national electrical codes, using wire size recom-
mended in installation sheet.
• Do not mount unit in ambient temp. exceeding published limits.
LIMITED WARRANTY
Seller warrants that the product hereby purchased is, upon delivery, free from
defects in material and workmanship and that any such product which is found to
be defective in such workmanship or material will be repaired or replaced by Seller
(Ex-works, Factory, Watertown, Massachusetts. INCOTERMS); provided, however,
that this warranty applies only to equipment found to be so defective within a
period of 36 months from the date of manufacture by the Seller. Seller shall not
be obligated under this warranty for alleged defects which examination discloses
are due to tampering, misuse, neglect, improper storage, and in any case where
products are disassembled by anyone other than authorized Seller’s representatives.
EXCEPT FOR THE LIMITED WARRANTY OF REPAIR AND REPLACEMENT STATED
ABOVE, SELLER DISCLAIMS ALL WARRANTIES WHATSOEVER WITH RESPECT TO
THE PRODUCT, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE.
LIMITATION OF SELLER’S LIABILITY
SELLER’S LIABILITY TO BUYER FOR ANY LOSS OR CLAIM, INCLUDING LIABILITY
INCURRED IN CONNECTION WITH (I) BREACH OF ANY WARRANTY WHATSO-
EVER, EXPRESSED OR IMPLIED, (II) A BREACH OF CONTRACT, (III) A NEGLIGENT
ACT OR ACTS (OR NEGLIGENT FAILURE TO ACT) COMMITTED BY SELLER, OR (IV)
AN ACT FOR WHICH STRICT LIABILITY WILL BE INPUTTED TO SELLER, IS LIM-
ITED TO THE “LIMITED WARRANTY” OF REPAIR AND/OR REPLACEMENT AS SO
STATED IN OUR WARRANTY OF PRODUCT. IN NO EVENT SHALL THE SELLER BE
LIABLE FOR ANY SPECIAL, INDIRECT, CONSEqUENTIAL OR OTHER DAMAGES OF
A LIkE GENERAL NATURE, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS
OR PRODUCTION, OR LOSS OR EXPENSES OF ANY NATURE INCURRED BY THE
BUYER OR ANY THIRD PARTY.
UE specifications subject to change without notice.
Response Codes
Code
Description
0
Success
2
Invalid Selection
3
Passed Parameter Too Large
4
Passed Parameter Too Small
5
Too Few Data Bytes Received
6
Error (Device Specific Command Error)
7
In Write Protect Mode
8
Multi-Definition Warning
Update Failure
Set to Nearest Possible Value
All but running delayed responses flushed
9
Multi-Definition Error
Lower Range Value too High
Applied Process too High
Not in Proper Current Mode
10
Multi-Definition Error
Lower Range Value too Low
Applied Process too Low
Invalid Local Panel Code
11
Multi-Definition Error
Upper Range Value too High
In Multi-Drop Mode
Invalid Device Variable Code
Trim Error Excess Correction Attempted
Cannot Lock Panel
12
Multi-Definition Error
Upper Range Value too Low
Invalid Units Code
13
Multi-Definition Error
Both Upper and Lower Range Values Out of Limits
14
Multi-Definition Error
Span too Small
New Lower Range Value Pushed Upper Range Value Over Limit
16
Multi-Definition Error
Invalid Analog Channel Number
Access Restricted
17
Invalid Device Variable Index
18
Invalid Units Code
19
Device Variable Index Not Allowed
20
Invalid Extended Command Number
28
Invalid Range Units Code
30
Command Response Truncated
32
Busy
33
Delayed Response Initiated
34
Delayed Response Running
35
Delayed Response Dead
36
Delayed Response Conflict
64
Command Not Implemented
