Udoo VISION User Manual Download Page 14

Page: 14 / 67

VISION

1.10

Reference specifications

Here below it is a list of applicable industry specifications and reference documents.

Reference

Link

ACPI

http://www.acpi.info

AHCI

http://www.intel.com/content/www/us/en/io/serial-ata/ahci.html

DDC

http://www.vesa.org

DP, eDP

http://www.vesa.org

Gigabit Ethernet

http://standards.ieee.org/about/get/802/802.3.html

HD Audio

http://www.intel.com/content/dam/www/public/us/en/documents/product-specifications/high-definition-audio-specification.pdf

I2C

http://www.nxp.com/documents/other/UM10204_v5.pdf

Intel

Front Panel I/O connectivity DG

http://www.formfactors.org/developer/specs/A2928604-005.pdf

M.2

http://pcisig.com/specifications

MMC/eMMC

http://www.jedec.org/committees/jc-649

OpenCL

http://www.khronos.org/opencl

OpenGL

http://www.opengl.org

PCI Express

http://www.pcisig.com/specifications/pciexpress

SATA

https://www.sata-io.org

SD Card Association

https://www.sdcard.org/home

SM Bus

http://www.smbus.org/specs

TMDS

http://www.siliconimage.com/technologies/tmds

UEFI

http://www.uefi.org

USB 2.0 and USB OTG

http://www.usb.org/developers/docs/usb_20_070113.zip

USB 3.0

http://www.usb.org/developers/docs/usb_30_spec_070113.zip

Intel

Atom Apollo Lake family

https://ark.intel.com/content/www/us/en/ark/products/codename/80644/apollo-lake.html#@Embedded

Summary of Contents for VISION


































































Search results

Summary of Contents for VISION

Reviews:

Brands by name

Popular brands

Udoo VISION, User Manual

Search results

Summary of Contents for VISION

Reviews:

Brands by name

Popular brands