manualshive.com logo in svg

Ude IPU-1025, Installation, Configuration And User Manual

Share
Download
Ude IPU-1025 Installation, Configuration And User Manual Download Page 22

29

22

IPU-1025

5.4. DEVICE CONFIGURATION. (Device).

This section allows you to configure the analog parameters and modes of the device.

IPU-100 Mode.

SPEAKER (Receiver)

TREAMING (Emitter).

IPU-100P (Normal).

To set the mode of the IPU-1025 between 4 options:

.

The IPU-1025 behaves as audio reception point and is ready to receive calls ONLY. This option is set by Factory default.

The IPU-1025 will act as an audio emitter point and it will be ready to make calls ONLY (VOICE/MUSIC). The streaming is
always done to the extension configured as "Default Call" in the SIP configuration section..

The IPU-1025 will act as an audio emitter point (VOICE mode) being synchronized with the IP Paging Desk connected to the
AUDIO LINK. For more details refer to the User Manual of the IPU-100P IP Paging Desk.

AMPLIFIER (Receiver)

.

The IPU-1025 behaves as audio reception point, allowing you to receive IP calls, with the difference that when it receive no IP
calls, then IPU-1025 will amplify the audio signal present at the INPUT connector (MIC/LINE).

Attention!

Do not use the IPU-100P Mode when no IP Paging Desk is connected to the AUDIO LINK

terminal as it can lock the IPU-1025 temporarily until you perform a reboot of the device.

VoIP Codec.

- G.711 (u-Law).

- G.711 (a-Law).

- G.722(ADPCM).

Allows selection of the codec to be used to encode both outgoing and incoming calls when the audio source is a microphone.
The options are as follows:

8 bits logarithmic compression and 8KHz sampling frequency. Quality: Low (As Factory Default).

8 bits logarithmic compression and 8KHz sampling frequency. Quality: Low.

8 bits Adaptive Linear Compression and 16KHz sampling frequency. Quality: Medium.

16 bits without compression and 8KHz sampling frequency. Quality: Good.

-

-

PCM Uncompressed (8kHz).

PCM Uncompressed (16kHz).

16 bits without compression and 16KHz sampling frequency. Quality: Very Good.

5.- DEVICE CONFIGURATION (WEBSERVER)

610.440A

Installation - Configuration - Use - IPU-1025

IPU-1025

Rev. 1

Summary of Contents for IPU-1025






























Reviews:

No comments

Brands by name

Popular brands

Load more brands