UCL SWIFT SWIFT KF4, User Manual

Page: 15 / 29

6.2 | HEATER
To display heater mode, press and then select “HEATER” from the menu using . The selecting screen is
equipped with various heater modes to facilitate easy selection. Heater mode can be expanded and saved for
up to 100 modes. Heater mode Nos. 1—16 cannot be deleted or replaced.
[Outline of heater mode]
Choose the right mode for each sleeve tube type and SOC. Otherwise sleeve tubes do NOT shrink
properly.
For the SOC, operators must use UCLSWIFT standard products. For other sleeves, see manufacturer
specifi cations and adjust manually.
Heater modes specify temperature, time and heating location on the heater plate.
6.2.1 DELETION
First, select a heater mode by pressing . Press to delete. Mode Nos. 1—16 cannot be deleted.
27 28
SET VALUE DESCRIPTION
60mm
40mm
60mm IS-60
45mm IS-45
S09
S09-C
S20
S30
S30-C
LC09/20-C
ST09-C
ST30-C
Standard 60mm micro sleeve
Standard 40mm micro sleeve
60mm micro sleeve
45mm micro sleeve
45mm sleeve for 0.9mm cable
22mm sleeve for SOC (SC-0.9mm)
45mm sleeve for 2.0mm cable
45mm sleeve for 3.0mm cable
32mm sleeve for SOC (SC-3.0mm)
25mm sleeve for SOC (LC-0.9, 2.0mm)
28mm sleeve for SOC(ST-0.9mm)
36mm sleeve for SOC (ST-3.0mm)
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 38
6.2. HEATER
To display heater mode, press and then select “HEATER” from the menu using
. The selecting screen is equipped with various heater modes to facilitate easy selection.
Heater mode can be expanded and saved for up to 100 modes. Heater mode Nos. 1~16 cannot
be deleted or replaced.
[Outline of heater mode]
SET VALUE DESCRIPTION
60mm Standard 60mm micro sleeve
40mm Standard 40mm micro sleeve
60mm IS-60 60mm micro sleeve
45mm IS-45 45mm micro sleeve
S09 45mm sleeve for 0.9mm cable
S09-C 22mm sleeve for SOC(SC-0.9mm)
S20 45mm sleeve for 2.0mm cable
S30 45mm sleeve for 3.0mm cable
S30-C 32mm sleeve for SOC(SC-3.0mm)
LC09/20-C 25mm sleeve for SOC(LC-0.9 , 2.0mm)
ST09-C 28mm sleeve for SOC(ST-0.9mm)
ST30-C 36mm sleeve for SOC(ST-3.0mm)
Choose the right mode for each sleeve tube type and SOC. Otherwise sleeve tubes do NOT shrink
properly.
For the SOC, operators must use UCLSWIFT standard products. For other sleeves, see
manufacturer specifications and adjust manually.
Heater modes specify temperature, time and heating location on the heater plate.
!
CAUTIONS
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
6.2.2 REPLACEMENT
Select a heater mode to replace, and press to display heater modes on the screen. Select desired heater
mode and press to replace with the selected mode.
General modes Nos. 1—16 cannot be replaced.
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 9
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera’s focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera’s focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 39
6.2.1 Deletion
First, select a heater mode by pressing . Press to delete. Mode Nos. 1~16 cannot
be deleted.
6.2.2 Replacement
Select a heater mode to replace, and press to display heater modes on the screen. Select
desired heater mode and press to replace with the selected mode.
General modes Nos. 1~16 cannot be replaced.