background image

6

© 2021 Ubicquia Inc.  |  All rights reserved. Patent pending. Public use approved.  |  2058 v2 October 2021

6.3

   Line up the NEMA plug on the 

UbiHub with the NEMA socket 

on the luminaire. The UbiHub 

should be slightly off-angle of 

the luminaire by 15 degrees once 

inserted. 

NOTE:

 Make sure the NEMA 

plug and NEMA socket remain 

parallel during installation.

NOTE: CREE fixtures/NEMA will 

need to be locked in

6.4

   Once plugged, rotate the UbiHub 

towards the pole to lock the NEMA 

connecter in place. Stop once the 

clamp is aligned with the pole.

6.6

   Adjust the clamp vertically as 

necessary to ensure the device 

is parallel with the bottom of the 

luminaire to ensure there is no 

undue stress or strain on the NEMA 

socket.

6.5

   Close the clamp around the 

pole by rotating the clamp latch 

upwards and securing with the 

swivel locking nut. Use 1/2” 

socket to tighten the locking nut 

to 40 in-lbs torque.

B.

Pull the inside (grey) section of

the NEMA connector out slightly

and twist until the N > is facing in

the correct direction (away from the

luminaire pole).

A.

Use a screwdriver to remove the

two screws. Unscrew the NEMA

connector and lift then turn the

NEMA connector until the N > is

facing in the correct direction (away

from the luminaire pole).

Summary of Contents for UBH-H-AI











Reviews: